hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
After the command "zdo mgmt_lqi 0x0000" is successfully used to obtain the short address of the terminal device, you cannot obtain the short address of the terminal device...
Current I am using nRF52840 Dongle to develop a Bluetooth PC Tool base on nrf_ble_driver_obj_sd_api_v5 which shared on https://github.com/NordicSemiconductor/pc-ble-driver...
Hi Nordic Dev Team,
I need suggestion on how to achieve this. My microSD saves chunks of 50kB raw data.
I would like to retrieve this data once connected to the phone...
Hello,
I am trying to receive advertised data by a sensor which is easily detected at nrf connect app and whenever data changes i am able to see the change in data on nrf...
I am trying to send a lot of data and I am trying to do this with notification. As I understood notification do not need acknowledgment and should not use que for messages...
Hello,
I am using SEGGER embedded studio to develope a project. I want to know how can I know the flash and SRAM use of part code. Because I have many files. After I build...
I am using the nrf9160 for an OTA firmware update application. After going through a lot of tickets and some documentation regarding the nrf, I have not been able to find...
I want to use the register of Nordic's P0 port directly to set 1 or clear 0. Like this,
p_reg-> OUTCLR = clr_mask;
P_reg - & gt; OUTSET = set_mask;
p_reg-> OUTCLR...
Currently we are developing against hardware sensors etc. that we have installed in our warehouse
It would be great to be able to develop remotely (ie. from home) without...
Hello Nordic Support Team,
I'm using nrf52840 DK for DFU update over ble with nrf5 sdk previously it was working fine and i was using nrfutil tool to generate settings,...
Hi,
I have downloaded the nRF5 sdk v17.1 and used the peripheral blinky example with pca10056e and S112 soft device and modified the preprocessor defines and this example...
Hello Everyone,
I am working on NRF52840 and we had enabled the APPROTECT feature in our firmware. The code for implementing this is as follows:-
void init_mem(void) ...
Hello,
I know that the bt_ctlr_set_public_addr() interface needs to be called before enabling Bluetooth, and this bt_id_create() .
But I read the description of bt_id_create...
Hi,
The nPM1100 Specification states in section 7.2 that:
An application should not be supplied directly from VBAT because it can disturb the battery charging process...
