hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hello Nordic Team,
We need to start RF performance tests using CMW500. we have access to UART pins of nRF52840 in our DUT which can be used to connect UART-USB adapter to...
Hello Nordic, I am using
nRF5_SDK_17.0.0_9d13099,
IDE Segger V4.52c
soft device s132
Can I transfer 8208 bytes on I2C with nrf52832 with EasyDMA, ignoring the MAXCNT...
Hi,
I try to understand the power consumption of the UDP example for NRF9160 with PSM.
I'm using the default configuration: RAT="00000000", RPTAU="00100001", no eDRX,...
Hi all,
I am trying to interface a BLE mikrobus module onto a Yocto based Linux SBC. I need to use Zephyr's hci_uart example to flash it onto the module, the mikrobus...
Hi Dev Team,
I am running a program that takes in sensor data at 10 min intervals and publishes it to my server through MQTT at 1hr intervals.
I have different threads...
Hi, I am using Zephyr BLE stack to check the HCI testing og the nrf52840_pca10056 module. I am useing Windows Subsystem for Linux for Ubuntu toolchain. While using the make...
Hi,
I am planning to buy a nrf9160-DK to build a BLE LTE-M gateway. I would like to ask if the gateway is able to communicate with a private MQTT broker/server instead of...
my project is freertos+nrf52832 based the templete in SDK; A sensor pin is connect to P0.17, and I configure it low to high level trigger interrupt.In the handler I will call...
Hi all,
I am using two nrf52840 boards and a Light-Switch example included in the mesh SDK. I want to observe packages sent by the client and packages arriving at the server...
SDK: NCS 1.4.0
board: nRF9160-DK
sample: lwm2m_client
Question:
I am testing SERCOMM module and nRF9160-DK, but there is difference in registration procedure .
When...
Hello, I migrated codes that I believed to be relevant to the UART output to a new project, namely the uart_init function and others, and it worked in main.c, which is where...
I am trying to use the connectivity firmware with an NRF52840 dongle to communicate with an nRF52840-dk through the nordic UART service, but I am unable to use the pc_ble_py...
Hello,
I am curently working on project with a nrf9160. I will use the nrf9160 as modem controled by a nrf52840 and command AT. I will send data true GSM every 12 hours...
