hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hello,
How the modem selects it band of operation. Is it done automatically selected by the modem after registering to the base station? or is it assigned by the base station...
The modem firmware version 1.1.4 has been certified by Verizon, and the corresponding NCS version is v1.4.2. Now Nordic has released the NCS SDK version v1.5.0. This version...
To the kind attention of Nordic support team,
if it is not much trouble I would like to know what you consider a good/acceptable ble antenna efficiency in
desktop environment...
Hi,
I am using an nRF52832 with S132 and SDK v15.0.0 and already read in the forum about issues related to the SAADC calibration (inlcuing the erratum [86]). The problem...
Hi Nordic,
I have 2 charac i can write, let's name it A and B.
When i write into A, it trig ble_A_on_ble_evt , BLE_GATTS_EVT_WRITE , no problem.
But w hen i write...
I started developing a project on nRF52. My task is to read the value from the light sensor (phototransistor).
The sensor is connected in this way:
my code:
init...
when i Use 2.4G radio to communicate with other modules,like cc2510, i have many questins:
1. as we known that CC2510 ' modulation format of the radio signal ,MSK is only...
Hi,
Maybe this is obvious, but I couldn't find the answer anywhere online. When I power my dongle from an external 3V3 source, can I still plug it in to my computer and...
Hi, during my tests, I use an NRF52 Dongle with the nRF-Connect app as a USB/BLE interface, but now I need to handle some custom data. I have seen that the dongle uses a COM...
Hi!
I'm working on using the SAADC in 14-bit sampling mode (oversampling set to x2) using nRF SDK 17. The supply voltage for my chip is 3.3V, and I have the reference...
Hi @ all, can anyone here recommend me a suitable chip antenna, preferably one with matching regulatory documents in combination with a nRF52840 MCU.
Thanks and best regards...
I am trying to flash a NRF52832 using the J-link EDU mini in the Arduino IDE but I am having no luck.
I have successfully downloaded... 1. J-Link Software and documentation...
While digging for electrical information I came across :
.63ma using HFINT or 1.58ma using HFXO ?
So I hunted down HFXO to see how to switch between them:
But nothing...
please advice how to add "QDEC_NRFX" to the project configuration of 5340
1. it's not on the default menu config
2. I have tried adding under "ncs\v1.4.99-dev1\zephyr...
