Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
I am using Segger Embedded Studio IDE v4.52 (64-bit) to develop an application using nRF5340pdk.
My question is this, I cannot find any of the Preprocessor or compiler...
Hi.
I am developing using nRF52820 with SDK 17.0.0 . I test the USBD using the example code(\nRF5_SDK_17.0.0_9d13099\examples\peripheral\usbd_hid_generic), but the problem...
Hi,
I would like to know if it's possible to read advertising data when connecting to the peripheral.
My problem is sometimes when i read the adv data, and then try to...
Hi,
I try configure 2 gpio pins with opposite pull state, one NRF_GPIO_PIN_PULLUP, other NRF_GPIO_PIN_PULLDOWN :
nrf_drv_gpiote_in_config_t in_config = GPIOTE_CONFIG_IN_SENSE_LOTOHI...
Hello
We are working on BLE remote based on nRF52810. We are operating it through coil cell. Please let us know is there Internal battery monitoring feature supported by...
Hi--
I am running a application that executes in the bootloader region of memory (0x70000 to end of memory), and is using FStorage to overwrite the application memory space...
Hello, I am on a NRF9160-DK and I am using SDK 1.3.0 I am working on the AWS_FOTA project. I'm trying to configure the sending of a message in MQTT when pressing a button...
Its a first time, we are using the Nordic product. Please let me know how the step-by-step software installation procedure and would like to know the software cost as well...
I am trying to embed CTS in my code. I have included #include "ble_cts_c.h" Then I made changes to sdk_config.h I have this enabled in sdk_config.h:
Yet I am unable to...
Hi,
I made a demo app using advertising and scanning functionality in SDK 16. Now I'm trying to get it working in our company's full blown C++ framework, which is based...
Hello to everyone, I have a nrf52840 dk device running Zephyr RTOS. I have flash an app to the start address 0x00 and a second app to 0x2000 address. While I am pressing a...
Hi, I want to secure connection between our device (nRF52840 or nRF51822) and a smartphone.
I find that LESC uses ECDH which is more secure than RSA in same key length....
I need a full datasheet for the nRF52805 device - I could not find the information on the website, which is visually impressive but technically very unclear in my opinion...
im trying to use the functionality of notification using ble_app_hrs_freertos
i have created one service, one characteristic , timer and timer handler.
while debug the...
