I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hello, We have been using the PCA100059 version 1.0.0 dongle with a custom firmware which fails to run on the new PCA10059 version 1.2.0. Unfortunately there doesn't seem...
Hello,
Im a beginner in microcontrollers programming, just started with the pca10056 and pca10059. Im aiming to develop a beacon scanner for pca10059, to send data via usb...
I compiled and debugged the PCA10040e ANCS example (ie emulating the 52810 using the 52832) from SDK 15.3 - successfully. But I wanted to turn off code optimization to facilitate...
Hello,
As many mobiles do not have NFC I would like to use LESC OOB pairing with an QR-Code which could be shown on the device terminal. Well, I know where the NDEF message...
SDK version :15.2
question； when i use app_timer , i got interrupt which is not i wanted.
i creat and start timer :
app_timer_create(& m_timer ,APP_TIMER_MODE_REPEATED...
I'm using nRF SDK V15 with nrf52DK board, running the ble_app_hids_ms example.
I I want to have continuous non-stop advertising duration, should I have both APP_ADV_FAST_DURATION...
Dear Sir/Madam,
My question regards the behavior of the EasyDMA during the transfer of data to / from a serial peripheral like SPI or UART.
Let's suppose that during the...
Hi all,
I using SDK 15.1 and 15.3 for test.
I am working with DFU for NRF52810.
I tried success for NRF52840.
But I can't update success for NRF52810.
Below is scrip...
I use the Firmware «AT host sample» on Thingy91. Then I connect to Swisscom network on band 20. The current consumption is about 3.5mA. Then I send AT+CFUN=0 or AT+CFUN=4...
Hi All
We are using nRF9160 DK, and we are working on ADC channel. we use This example of ADC. I am using single-ended with no over-sampling with a gain of 1/6, reference...
Hello
my setup is sdk 15.3, nrf52840, s140, open bootloader and an application.
Everything is merged, flashed and running and no changes are made at the standard addresses...
I am currently developing a peripheral app on a custom board with a nrf52832 chip on it and connecting to the device using QT's ble library. I'm having issues where my connection...
I want to turn on /off LED by advertising TX of BLE
peripheral : nrf52810 central : nrf52840 Specifically, peripheral performs advertising TX, The central processes LED...
