hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi
Can I think so,if subscription address is identical in multiple nodes,then they are a group?
If so:
the light_1&light_2 OnOff Server Model subscription address is...
hi,
I had the board run the following code to connect it to the cellular tower:
#include <zephyr.h> #include <stdio.h> #include <string.h> #include <lte_lc.h>
void main...
I tried to advertising eddy stone beacon from getting serial UART data. i merged 2 codes in ble_app_eddystone and uart code but one error become like
..\..\..\..\..\..\components...
Hello dear Nordic Developer and Hobbyists,
first of all I would like to thank the developer team for the nice mesh demo. It functioned well and explicates the concepts of...
Hi,
I am not getting any response from the previous ticket. Did it get accidentally closed?
Case ID: 225033
Can please someone look at it? We are in urgent need...
Hi, I have tried to run nfc example, but it doesn't working, accidentaly i have found out that if supply 3V nfc not working, but if supply 2.7V and less it works, what is...
Hi, I'm designing based on the Altium files, but I'm not an antenna expert so I would like to know if you have any antenna recommendation for a low profile, because the one...
Hi,
I'm working on nrf52832 NUS. When i connect to device with "nrf connect app" i can see the data coming from sensor. But few seconds later device disconnect.
When...
Hello
I have 3 nodes, 2 Thread CoAP servers and 1 BLE/Thread Coap client.
Let's call them THnode1, THnode2 and BLE_THnode0.
I do not know the IP addresses of any node...
Hi,
I use "printf" or "app_uart_put" function to print message to UART., how can I check "all of the data had been transmit out complete"?
Thank you,
Chianglin
Hi, I want to test sending multiple packets of data with each packet having the maximum possible size of 247 bytes. I am currently testing with nRF Connect app. When i try...
I use nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac.
Example nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\examples\thread\cli\uart\pca10056.
define BOARD_PCA10059.
...
I am using nrf51822. Separately BLE and flash are working perfectly alright. But when I comment err_code = ble_advertising_start(BLE_ADV_MODE_FAST); this line flash is working...
Hello,
As per my understanding, SPP was supported by BT Classic and no more supported in BLE. I have a device, which runs SPP. It has to be connected to the BLE client....
Hi, I am now developing a product which uses nrf51422 chip. In this product, I use buttons to turn on and off (since I don't have hard-power cut off circuit, we use system...
