I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello, if I disable interrupt on nrf51xxx device, function sd_ble_tx_buffer_count_get will simply run right into hard fault handler, without returning anything.
I do not...
Hi,
on NRF51 BLE peripheral I want to implement authentication, so only selected BLE masters have access to my BLE peripheral.
There is a password known to BLE peripheral...
Regarding the RTC prescaler of nRF51822,
I found out that it is the following.
Timer and RTC prescaler behavior by TASKS_CLEAR is different,
When TASKS_CLEAR is executed...
My company is making capacitive touch plates and to make them smart, app is used.We are using NRF24L01+ for rf communication between device and app. Our sockets and hub with...
I did some modification from radio test example.
But I don't know why the function "rand8" never ending.
In the function, rand8,
NRF_RNG->EVENTS_VALRDY = 0;
while (NRF_RNG...
Hi,
I have been trying to get up and running since the first DK was released for nRF52x and I am yet to have installed a working development environment. I have tried to...
I'd like to use a DMA channel on the nRF52 to copy RAM from one block to another. However, there doesn't appear to be any DMA controllers that are not directly associated...
Hello everyone
I'm trying to disable advertising but it doesn't work in some cases, I don't really know why. Here is my pretty simple piece of code:
/* Disconnect and...
www.keil.com/.../uv4_db_dbg_evr.htm
www.keil.com/.../EventRecorder.html
Keil worked in a new EventRecorder feature that uses some SWD buffer memory to push data out...
Hello,
A question to understand please. A lot of issues still unfixed in rev 1, but are known for a long time (see errata docs). Like SPI with RX = 1, DCDC -4dB on RF,...
Hello, I try to run the sdk example for adc, i set an input voltage in varying from 0 to 4.38 V in the pin 4 (AIN2), but the returned value didn't corresponds to the desired...
It there a specification for current draw during POR? (From time Vdd starts rising until cpu starts executing?) For nRF51 and 52.
I found this devzone.nordicsemi.com/....
(Hello! I'm drawing the module circuit base on nrf52832 with rfx2401 power amplifier (PA). As I understand it needs to set pins TXEN, RXEN to high level to activate this PA...
It may sound a bit old and you may have fixed them in latest Soft Device stacks however I wanted to share with you a couple of pairing issues we encountered with Soft Device...
