I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi Nordic Dev Zone, Ray Kampmeier here.
I'm building Direct Test Mode (DTM) into a production application that uses the 110 soft device. Unlike the provided Nordic examples...
Is there any way to integrate SoftDevice with entire project so I can get one hex from build? I am new to CrossWorks and nRF52 and I am developing BLE device. After getting...
I want to do firmware update over the air in a STM32F4xx microcontroller which is connected with nRF51822 chip via UART (TX, RX, CTS, DTR) and BOOT pins. ST microcontroller...
Hi
I can get the current time from the server using the time service characteristic. Which function should I use to set the RTC clock on the nrf 51 to the current time...
When I add a new server of my own service I got a problem.
when I set
BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM(&cccd_md.write_perm);
I can send data to iOS normal,but...
Sometimes I only need to send 4 bytes instead of twenty using a notification. I've noticed the init_len and max_len parameters but I'm under the impression that this will...
i am already using sdk 10. but when we have build boot-loader program. so, generate "nrf51422_xxac.hex" file. it's working for only nrf51422.. but not for nrf51822. so, how...
Is there any difference in RAM overhead with the new app_timer module on SDK 10?
I'm my application on SDK 6.1, I have 25 app_timers which run without any issue.
APP_TIMER_MAX_TIMERS...
I am setting up production testing of our product to do RF testing per app note AN34. We are using the nRF51822 on our product. I'm using Nordic's development kit and their...
Hello,
I am planning to use the nRF51 device in DTM and was looking for help on how can use it to control via USB/UART connection to PC using FTDI chip. All I want to do...
Hi Nordic,
I am having a problem with linking against either of the gazell gcc libs (gzll_gcc.a or gzll_sd_resources_gcc.a).
I'm using Yotta (MBED) and have taken the...
Hello,
we have an android/iOS app on a phone that is connected to my button (nRF51) and to a Bluetooth headset. The app is a kind of walkie talkie that transmit mono audio...
Hi, I'm working on a project where I'm trying to make an nRF51822 play a basic sound (such as a beep). Is there a recommended DAC that should be used with this particular...
