hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
i have installed segger ide and nrf connect for desktop for programm nrf9160 , i have successfully uploaded Blinky code (zephyr) .but now i want to create a new project ....
By default, CONFIG_ZBOSS_OSIF_LOG_LEVEL_CHOICE was set to ZBOSS_OSIF_LOG_LEVEL_INF. But I'd like to increase the log level to debug a problem I'm seeing. When I increase verbosity...
Whilst I recognise some of the NC pins on the nRF52833 are IO pins on the 52840, but I also noticed apin mapping difference on a common port...52833 A16 is P1.05 and whilst...
We are using SDK 15.3.0 and S140 v6.1.1 SoftDevice. We are using an external LF crystal with tolerance of +/-20ppm, and are therefore using
#define NRF_SDH_CLOCK_LF_SRC...
Hi,
As per this link , the memory requirement of Thread 1.2 based application in nRF Connect SDK is around 487KB, over which more will be added as per application development...
I flashed a nrf52dk - nRF52832 board with a sample project (peripheral_hr) and the name is displayed correctly in the nrf connect app and other BLE discover apps.
After...
I need twoADC channels. I tried to configure using :
CONFIG_ADC= y in prj file,
&adc{ #io-channel-cells = < 0x2 >; }; in overlay file .. the compile error appears as shown...
HI
I am using VS for the firs time and I am trying to build the project Blinky but when I try to add the blinky folder to applications to build I get
: Element with id...
Hi ,
I followed the DFU-OTA tutorial(DFU over Bluetooth) given below for nrf52833dvk. and it is successfully completed. Now the query is , once we shared the bin file from...
Dear,
I need to use nRF5_SDK_17.0.2_d674dde for nRF52833.
I saw the release note, it says it need SES v4.5.
But when I use SES v4.5 to download or debug.
The computer...
Hi,
My goal is to generate a GPIO or GPIOTE interrupt and inside the ISR sample 8-bits from GPIO.
I tried modifying two sample projects to achieve this, the NRFX and...
Hi Sir,
We reference example "/nrf/samples/bluetooth/hci_uart" and test on nRF52833.
Now we want to set the Tx power by sending appropriate HCI commands from the host...
When I get the first error in UART, the receiving of new characters stops (the transmittion continue working)
and I didn't find any solution to make RX (receiving characters...
Hello
I'm about to update from NRF SDK v1.8 to NRF SDK v1.9.1. We build our firmware for both NRF9160 but also for QEMU_X86 (simulation build). I noticed that since the...
