hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi to All Colleagues:
New to Nordic and its development platform. Finished installing required tools using nRF Connect for Desktop v3.10.0. Attempting to use nRF Connect...
Hi,
I'm investigating possible improvements to our custom firmware update architecture. I'm curious as to whether it is possible to run the SoftDevice from a location in...
I've just received nRF52840, it powers up and blinks as programmed and the buttons work. I hear the "ba bing" on my PC when it connects and disconnects, but the JTAG does...
Hi DevZone,
I need to change some defines in the ffconf.h file used by nRF5 SDK to set configurations for FatFS to enable use of f_findnext(), f_findfirst(), etc.
Is it...
Hi,
I have provisioned some nodes using interactive_pyaci successfully. Functionality is as expected. As a test, I then shut interactive_pyaci down, rebooted the nRF module...
Our Gateway uses a NRF52 and the sensors a NRF51.
Gateway is outside the freezer at + 20C and the sensor is inside the freezer at -30C.
What we see is the pairing becomes...
I'm working on a wireless musical instrument which requires a super low latency RF link. I previously was using NRF52810 and found that the latency was too high. The complexity...
Hello,
I'm a beginner ... I would like to connect a LoRa module (REYAX RYLR896) to send data from my nRF52840 Express to an Arduino UNO (with LoRa).
I don't know how...
Hello,
I am trying to work with the DFU examples provided with the SDK. My board is a custom USB dongle to which I need to add the bootloader. Following the steps from...
Is there a way to enable LE privacy for nRF52 DK in Bluetooth Low Energy App of nRF Connect for Desktop? I would like nRF52 DK to use resolvable private address when connecting...
hi, Im trying to read from a sensor register using TWIM peripheral on nrf52840 in blocking mode, but it wont work , doesnt freeze or anything .. just doesnt work
below you...
Hello,
I am trying to set system on mode in nrf52840 usb dongle.
This mode switched automatically by idle task, when there is no thread running.
There is no while(1...
Hello,
I m new to nordic in VS code. Bought two nRF5340 DK for ADC conversion and wireles data transfer.
Followed all Youtube install instructions "nRF Connect for VS...
Is it possible to communicate with the of nRF52840 through USB, for example using PyUSB?
If yes, is there any documentation that can help in this regard, e.g. documentation...
