HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Good afternoon.
We're using nrf Connect for mobile to perform DFU over BLE to an nrf5340-based module with firmware built using the nrf connect 1.6.1 SDK and its associated...
0 dBm TX @ 1 Mb/s Bluetooth Low Energy mode, Clock = HFXO 7.1 mA
Radio RX @ 1 Mb/s Bluetooth Low Energy mode, Clock = HFXO 6.5 mA
I want to know which example is tested...
The CAN controller MCP2515 should be connected to the Nordic DK NRF5340 by the SPI interface.
Communicate to Arduino uno
We were trying with CAN sample given
But this...
Hello,
I've tried to request the location via AGPS/PGPS via Location sample in SDK 1.8 but it seems that location is only working with the Cellular method.
I've tried...
Hello there, I am new to your product, and I am trying to understand your library logic and hierarchy. Right now I am trying to figure out what all of these prefix (such as...
Hi, I want to use an NRF52805 with a voltage to frequency detector. If I understand the datasheet, there is one timer/counter and RTC on that chip. Is it possible to set the...
Hello,
How do I deactivate/activate a SDA/SCL line?
I perform a test on an Icarus board with a VL53L1X sensor, everything works fine.
However, in idle/sleep mode, whether...
Hi,
I am unable to view the output of the prink statement on the SES debug terminal. I'm a beginner so please bear with my lack of knowledge.
Should I be looking for the...
I am trying to adapt the zigbee light_bulb sample to run on nrf52840-Dongle which does not have a QSPI flash chip. I see that it crashes unexpectedly during settings_subsys_init...
Hello,
We have product with nRF52811 as Bluetooth receiver and ESP32 as WiFi IC. The ICs have separate antennas, and nRF52811 has LNA with +12 dBm gain connected to antenna...
https://github.com/project-chip/connectedhomeip/blob/master/docs/guides/nrfconnect_examples_cli.md
uart:~$ clear date device devmem flash help history hwinfo kernel nrf_clock_control...
I have loaded up the altium design and can see the pad and via sizes used.
The drill size for the in pad via is very small (0.15mm) which will increase pcb costs and also...
*** Booting Zephyr OS build v2.7.99-ncs1 ***
nrf52840dk_nrf52840 system off demo Retained data not supported Busy-wait 2 s Busy-wait 2 s with UART off Sleep 2 s Sleep 2...
Hi,
Installed the toolchain, installed VS Code, and I think its all linked, but when I try to run even the most basic hello world program it just keeps throwing this error...
hi support team,
i am confused about "advertising extentions" part;
Inforcentor shows example for " Cycling Speed and Cadence Application" only support S132 and S140,...
