Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
Hi,
I am a bit stuck with configuring nrf5340 project to include the bootloader properly.
The SDK-toolchain I use is v3.0.2
What I need:
encrypted and signed update...
Hello,
We are trying to increase the upload speed of our BMD-350 module. Right now we are averaging about 3kB/s according to nRFConnect.
See attached image of upload...
Hi No rdic support tea m, I'm developing a custo m appl ication on t he Thingy53 and have encountered challen ges implementing two key features that a ren't cov ered in the...
Hi all,
I'm trying to set up MCUMGR on 54L15, such that it can receive images from my border router when they're in the same Thread network. I read that we can upload images...
HI
A phenomenon occurs where the current remains at 20mA intermittently.
Actually, the BLE specification states that RF TX/RX is less than 10mA....
I'd like to know...
We are in the process of porting from nRF SDK v15.3.0 to v17.1.0.
After updating, we’ve noticed that the device sometimes gets stuck. Investigation shows this is related...
I have a custom board using a nrf5340 and a st7789 display using spi and mipi_dbi. It's I have it working on a sample project and printing "Hello World" I was using nrfConnect...
Does this mean that Bluetooth LE Power Control (LEPC) feature is not at all supported by any of the Nordic chipsets? I am particularly curious about nRF54 series with the...
Hello,
Following this link I integrated the extended power save mode in my code,
I put the nrf7002 in extended power save mode after successfully connecting to the AP...
I'll preface this by saying I am new to developing on the nRF and the Zephyr OS.
I am just trying to set up a flash read/write module on my nRF52DK PCA100040 model. From...
I'm using pc-ble driver-master for programming. The hardware uses 52840 dongle and calls SD_API_V5. After I successfully connected, I sent a pairing request using the sd_ble_gap_authenticate...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
Hello all,
I’ve already looked in the following files:
C:\ncs\v3 .1 .0 \zephyr\ include \zephyr\bluetooth\mesh\ access .h
C:\ncs\v3 .1 .0 \zephyr\ include \zephyr...
VS Code extension updated to 2025.8.654. Now when I click flash it says
And sits there spinning. Running west flash manually works.
Extension Features > Runtime status...
Hi all,
Im testing the "periodic_advertising_example" but in wireshark (nrf52840 dongle) I can just receive the AUX_ADV_IND packet below. I can I see the periodic advertising...
