hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi, I want write code on rust, but build system of nrf sdk for nrf5340 too hard for creating bindings, so I decide to create own HAL on rust and embed it in C with BLE stack...
Hello,
I am working on a project that I built using the nRF52DK and then created a custom PCB. The software I wrote works on the DK with a breakout board for the RTC and...
Hi,
I am using a nRF52832,and to begin with I have to erase my memory,so I connect nRF52832 and click erase all.
The result is shown below,I wonder why I can't erase my...
After trials and tribulations I have finally gotten a pulse ox device to work as I needed to. I started with the health thermometer example in the 12.3.0 SDK which is the...
Hi
I tried following the eclipse installation tutorial: devzone.nordicsemi.com/.../
And after a while I got eclipse to handle the Nordic stuff, but when I try to import...
Please find attached several fixes for bugs / incomplete protocol implementation in the MQTTSN stack that we have identified for inclusion in future versions of the SDK. ...
The Thread SDK is pretty awesome! :) However, It does has a bit of a learning curve for me because it only uses UDP instead of TCP.
While searching I found an MQTT variant...
We're developing on a custom NRF53 board. With the I2C bus disconnected from all peripherals, but with external 10k pullups connected, we get the following waveform when attempring...
Hello,
We are working on a research project in Sheridan College to create an indoor positioning system using BLE 5.1’s Angle of Arrival feature. We noticed that nRF52833...
Hi,
I am using the nrf52840dk trying to connect my bike power meter over ANT+, to then forward data to cloud (will be using the nrf9160dk and then the thingy91 once I get...
Dear Support,
I'm evaluating a tiny BLE chip that we can do:
reading multiple three SPI sensors: pressure sensor, accelerometer, and FRAM.
So with your BLE chip...
Hi,
Using 52833 it seems that sometimes the radio quits responding, ie, it is in NRF_RADIO_STATE_DISABLED state and there is
no obvious way to get it out of that state...
Hello,
I'm trying to program the ble_app_uart example program from SDK 17.0.2 in Segger Embedded Studio using softdevice 132 to a custom PCB (with the nRF52832 chip) using...
Hi,
I am using nrf9160 to handle the MQTT protocol and collect the data packets from another microcontroller using the UART interface.
Sending the data to the server using...
Hello all,
since Tuesday I'm trying to get the example project ble_app_uart_c (SDK Version 12) running. Meanwhile I can compile the project without errors, but when I flash...
