Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi,
this is my first time trying to use nrf connectivity tools, and my setup is a bit strage (and I have no clean DK setup to compare with:-(
I have to update firmware...
I am developing an IEEE 802.15.4 Application on the nRF52840 using the Radio Driver (v1.8.0) . I have a problem with the transmit call function. Very often in nrf_802154_transmitted_timestamp_raw...
I wrote a program for nRF51822 and compiled it with keil. The app, boot, and sdk are combined and written to the chip. However, if I write using nRF Connect Programmer, it...
Hello,
Our custom board (nrf52832, S132) seem enter to the read back protection, J-Link could not connect to the target in any ways.
We tried the command "nrfjprog --recover...
The code is running on 52832 (BLE) and transmit msg over BLE (NUS) each time GPIO is active (GPIOTE).
But same code (after adding LE CODED Phy) is crashing once it reached...
I am trying to build the NCS sample project "peripheral_lbs" with multiple peripheral connections. Therefore I added the CONFIG_BT_MAX_CONN. Up to 20 the build is working...
I have a problem when activating the simcard via nrf connect. |
After several attempts, using the IMEI and PIN on the Thingy 91 product, i get the following error.
(There...
Hi. How do I advertise both heart rate service and current time service together?
Seems like the current time service overwrites the heart rate service.
I will appreciate...
Trying to convert a working sample for a BME280 sensor from I2C to SPI
nrfConnect 1.4 on nrf9160-DK
After looking at other SPI examples and noting the syntax I thought...
Hi,
i have changed uart pins to second port. After that it is not advertising. when i connect the FTDI converter to the uart pads from custom board, it starts working and...
Dear Devzone Community,
when trying to get the Zephyr SHT31 Sample running, I stumbled across an error which I was not able to resolve.
I did the following:
Add nrf9160dk_nrf9160ns...
I need to control the BLE ON/OFF state and send some data to MK81 via BLE through UART, we have estalished the Hardware connection between the nRF52832 chip and MK81,
How...
So, I am quite beginer with programming and working with this sensors and nrf, So I need your guys help.
I am trying to get the x,y,z values from the accelerometer of BMX055...
The nRF 52840 RSSI "meter" is not usable.
I tested in an RF (2.4Ghz) quiet neighborhood. Using a reference receiver, I measured RSSI variance around +/-3 dB (95% confidence...
