I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
this is my code on DFU function, I copy to the example of experimental_ble_app_buttonless_dfu on SDK12.1. I used nrfgo studio to program s130_nrf51_2.0.1_softdevice , boot_setting...
Hi,
I've been working on Thingy:91 under ncs tag 1.2.0, trying to develop simple application using NVS just to see how it works. Based on the zephyr sample I wrote the following...
Hi:
i have some problem about using ble.
in my application has a loop:
1.use ble adv,and Wait for a while，
2.close ble adv ,and using base radio funciton.(do stop...
Hi
I was able to successfully complete the RF output power measurement using nRF52840 DK with the help of Nordic devzone last time.
Based on successful measurement...
Hi,
I use proprietary service to transmit data between raspberry pi and nRF52840 DK. The example I referred to is below.
C:\nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral...
On the nRF52840, I know the PPI, and therefore any events/tasks, are synchronized to the 16MHz peripheral clock. Here is the quote from the documentation:
"On each PPI channel...
SDK:SDK15.3.0
Example: ble_app_buttonless_dfu project.
MCU : nrf52810
SD: s112
Hi,i want to know how to reduce the ram consumption on nrf52810 sdk15.3.0 ble_app_buttonless_dfu...
My program loaded to a nRF52840 DK unfortunately adresses ports P1.15 and P1.13.
Now the DK is not reachable for Segger IDE and can not be found as a USB device.
I can...
For the connection (peripheral) tab of the online power profiler, I have a question on why if my TX payload is 216 bytes which fits within the LL PDU size, the payload would...
Hi,
I do have customized services in my project to implement,I think it would be easy if we seperate service related functions from main to add services in further.To serve...
Hello, There were some problems while making Bluetooth packet readers.
Packet sent to another device cannot be read in BLE_GAP_EVT_ADV_REPORT.
Is there any way I can read...
Hi. I'm working with the nrf52832 chip, and had a few high level questions I wanted outside opinions on
1) I have a lot of trouble connecting to my BLE device. I frequently...
Hi Team,
We are going to use the NRF52832 soc with S132 Soft Device and SDK Version is 16 for our project purpose, we have some queries on this soc along with these SD and...
Dear,
I am struggle a problem in mesh communication.
Mesh SDK 4.1.0
I used dimmer example.
Two nodes can communicate and work perfectly fine, only if they are in communication...
