Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Hi, I am searching the nRF52810 product spec and see that with standard drive, maximum GPIO output current appears to be 4mA. However, this spec is given for when the output...
Hello, I am working on SDK 1.3.0, I have an NRF9160DK and I am migrating to a custom NRF9160, I would like to output the log by moving the pins of the UART. However, it is...
We have ported from SDK v15 to v15.3 but now have a problem getting the USBD to start.
Below is a sort of pseudo-copy of our USB init routine which is working for us on...
Hi,
On Nordic SDk 15.0, I have observed that USB CDC ACM Example is not working in interrupt mode on nrf52840 Evaluation kit.
But I have tested USB CDC ACM Example in...
I'm experimenting with nRF52840 DK
However, using break points in the main loop causes 'app_error_fault_handler'.
using the iar compiler. What's the cause?
Hi~
I have a question about the SAADC.BLE Connect Mode. When I turned on Saadc LP mode, the power dissipation was 0.02mA for single-channel sampling, but 0.5mA for dual...
Hi All,
I have looked through the devzone and cannot find a solution to this. I am using the nRF52832 SDK 15.2. Working with a BNO080 IMU over TWI.
I need to read more...
I have bought new thingy 91 from mouser. Com. I burnt the latest pre complied hex file for assist tracker. I am getting all data except gps.
it is not getting connected...
I have a custom firmware developed on a nrf52832 SoC. I would like to know if i could see nrf logs such as nrf_log_info and nrf_log_debug via bluetooth? if this is possible...
Hi!
I want to use a TensorFlow Lite for microcontrollers model in my existing project built on top of the nRF5 SDK. However, as outlined in the nrf-tensorflow example ,...
Hi ,
I has been using NRF9160's AT client mode to connect with CMW500, however I found some problem.
The following is the command log that I used to send via UART. However...
I'm working on code that needs to discover services on the central so I'm using ble_db_discovery_start. However, I notice that if the connection handle passed into this does...
I am trying to measure frequency of a gpio pin. I am using the code from the below thread -
https://devzone.nordicsemi.com/f/nordic-q-a/9036/measuring-input-gpio-pin-frequency...
Hello,
About 2 months ago I upgraded my project to SDK 17.0.0 (from SDK 15.0.0).
When I opened the datasheet recently I found that a newer version - SDK 17.0.2 is now...
Hello,
Im trying to implement FOTA on the nrf9160. Currently my first version is working however I would like to decrease the amount of data used in the process. According...
