I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
I have peripheral BLE device which can have several centrals in its whitelist. It should be able to connect to central with higher priority first, for example: device have...
Hi
I was using sdk 14.0.0. And I was adopting s332 as a soft device version and I was developing. However, when I go to Nodoric homepage and look for information, there...
I have an application for the nRF52832 which is working fine on SDK 12.3 and I am trying to port it over to SDK 14.2.
After some tweaking I have got the application ported...
I used example ble_hrs_freertos_app of SDK nRF5_SDK_14.1.0_1dda907.
I added one task for LCM (XPT2046) in the example.
i used the function :
When added the display...
Hi,
IC : nrf52832
SDK : Mesh_v1.0.0
I am testing the light_switch demo of the Mesh_v1.0.0.
I don't have 32kHz osc on my server board, so I have to change the clk...
Connect USB to PC, no "JLINK" device. But connect USB to PC and press reset button at same. I can see "BOOTLOADER" device.
How can I get my board to normal?
I am trying to create a network mesh using the multiperipheral example.
In the original version the communication is possible only:
central >> peripherals
peripferals...
Hello,
I am wondering if you have any plans for implementing a Softdevice that supports BLE mesh network on nRF52832 in near future?
If not, if I were to implement it...
I'm reading about beacon scan response requests and scan response packets, where a client (like a phone) can request the beacon respond back with local name and other info...
Hello,
I need to implement mesh networking capability in the beacons which are ble5. Can anyone explain me how do we achieve that?
I want send specific data via one...
Hello,
I have nrf52832 and sdk14.1.
Everything works fine but after starting the device i get this information and there is no further progress from there on:
<info>...
Hi,
I need to make two FSRS to read and display the output simultaneously. So, initially I had to get the ADC values from two analog pins at the same time. After struggling...
Hello all:
I have a big problem，I use SDK13.1, softdevice is S132_V4.0.2.When the program starts executing scan_start(),the program crashes.
At first I thought there is...
I'm developing a minimal bootloader on the nrf52832 that just reads/writes flash and decrypts some data already present in flash. I'm using the Bluetooth Spec's own sample...
