Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
OK, there are multiple versions of:
nRF51 chi
PCA10028 dev board
example projects
SDK
soft device
Keil dev environment
I getting all sorts of errors...
I'd like to optimize RAM usage due to lack of memory.
According to the release note of S130, the size of the GATT server attribute table can be set.
To get more RAM for...
First of all, I managed to successfully upload S110 and dfu bootloader (from SDK 9.0.0) individually to nRF51-DK board via OTA DFU using the Master Control Panel app. Initially...
I'm trying to get a DFU bootloader compiled for S130 8.0
In Keil the default dual bank compiles to over 7k
Total RO Size (Code + RO Data) 12608 ( 12.31kB)
Total RW Size...
Hello,
I want to save some structs to flash using pstorage with S130. What would be the best way to achieve this?
The struct consists of message, deviceID.
The whole...
I am designing a NRF52 based device. Do I need to add ESD protection circuits on PCB for any pins on NRF52? The initial device I am making is for prototyping a system. so...
Using nrf_delay_ms() can be energy consuming and indeterministic. I am trying to use application timers (from "app_timer.h") in nRF SDK 8.0. The way I did could be partially...
In a previous excellent answer Ole Morten explained how to calculate the maximum throughput of transmissions using notifications . I'd like to know what the calculations are...
Hi,
I am a newbie. I understand that a similar question was asked earlier, but I couldn't get an answer specific to my questions. My goal is to sample an analog signal at...
Hello,
not strictly an nrf question, but I am having trouble communicationg with the developer dongles under OS X. I am using screen to connect to my terminal and the input...
Nordic has show coffee machine using BLE IPV6. The BLE chip on coffee machine shall work as Master for IPV6 communication with internet? If so, does this chip drain much more...
Hi,
I would like to communicate nRF24L01 + module 2 but I'm facing a strange problem . I checked the registers . The data is loaded into the transmitter in the FIFO . I...
Hello!
I just want to change the outcome of Button 1 press action in my nRF 51 Dk. For example, instead of toggling led 1, I want to toggle pin 5. How to actually do that...
I have nrf51822 s130 sdk v8. When I use spi master in main loop the it works fine. When I start to use SPI master inside ble event then I dont get start, cancel or complete...
