I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
I just want to handle phone simple call event from iphone4s.
How can I do? Is there any other way to do this?
There are so many media key in hid profile, is there any...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi guys,
is it possible to get the mac address of the connected device?
Didn't find anything in ble_evt_t ..
Thanks!
Edit:
Sorry, i found it:
its in the ble_evt_t...
i am new to nfr51822 and i am doing project on indoor localization in which i need to read the RSSI values of bluetooth. so how i read these values? and i have setup the evaluation...
Hi !
I would like to know if there is a nAN-36-like application that also implements the radio functionity.
I would like to send a raw radio message to other devices...
HI：
I use Bluetooth capture crawl data. I want to see the data in DEBUG in?I can not see Adv PDU Header among type TxAdd RxAdd PDU-Length data in the code, AdvA which data...
Hello
I am developing a health fitness watch using the nRF51822 System-On-Chip. I am interested in acquiring an organizationally unique identifier that can be then be implemented...
Dear Developers,
At the moment I'm writing some software to develop an Android App. I'm using nrf8002. When my app connects to the nrf8002, I'm able to read battery level...
I am trying to use the nrf8002 for proximity type application. Right now I have a prototype working with a speaker and LED and I can light up either one using an app. What...
Hello every boby,
I'm a newbie in PIC programming and I hope something could help me to start interfacing the nRF8001 with a PIC. My schematic is already done but I don...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi
I'm using the Eval Kit PCA 10001 V2.1.0 and Nexus 5 with new Android version 4.4.2. Connecting to the Eval Kit works just fine, but when i perform a service discovery...
I have an nRF51822-based peripheral using the SoftDevice 110 v7.0.0 and SDK v6.0.0. The peripheral uses two custom characteristics under a single custom service. I'm using...
Hi
I'm using sd_app_evt_wait(); to go into low_power mode.
For some reason it comes back immediately, but I can't figure out why.
If I call it a second time it stays...
Hi,
I'm trying to flash the S110 onto my nrf51822 SoC, but nRFgo gives me the following error. (Also, hitting recover just gives me an error: "an error condition was detected...
