VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
Title: SoftDevice Controller: 100% connection establishment failure (HCI 0x3E) with SKY66112-11 PA active
Hi Everyone,
I am working on the following development project...
Hi,
I'm using the Thingy:91 X PCA20065 rev 2.0.0 as a reference for a new nRF9151 design and I have two questions about the QM13345 configuration.
1. LUT
The Thingy...
I have been testing the HTTP FOTA procedure as documented here using the 1.5.0 test diffs as provided in .
Many of the messages output by the modem in this upgrade process...
Hello,
We are seeing a west build reproducibility issue on nRF Connect SDK v3.4.0 that we have narrowed down, through extensive elimination, to the compiler's code generation...
**Setup**
- Custom board, **nRF54LM20A** , first bring-up. The SoC is powered from an
nPM1300: BUCK1 = 1.8 V feeds VDD.
- External **J-Link** (firmware compiled Jun...
Hello,
I have a tight loop with strict timing requirements that I'd like to run on the FLPR core of the nrf54lm20. In each iteration of the loop, i need to write data to...
Hi，
When we draw PCB, we also need to design it like your DK board? There are several square copper skins under the chip, the middle of which is grounded, and the other...
I have nrf52840 DK board, running cutom image that implements BLE central, constantly scanning on coded (S8) phy. Trying to add NFC T2T tag, and it doesn't work. Disabling...
Hi,
While characterising low-battery behaviour of the nPM1304 on the nPM1304 EK I see the following:
1. With VBAT above ~2.4 V, Ship mode current is ~0.40 µA, as expected...
In the bare metal SDK, for the cgms routine, if we switch to the internal LRC, how should we configure it?
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC =y
After making this configuration...
Hi! I know that FindHub is supported on nRF Connect SDK, but I'm wondering if there is any support for it on nRF5 SDK for the nRF52840? The use case would be adding the feature...
Hi,
I'm using the Thingy:91 X PCA20065 rev 2.0.0 as a reference for a new nRF9151-LACAA1A design, and I would like to make sure I understand the recommended correction for...
I am beginning to work on a next generation of environmental sensors. The current group of sensors use the i2c, or oneWire communications bus. The current standard micro-controller...
