I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi! Please, excuse the probably stupid question but I'm a real newbie. I'm trying to perform a long range coverage test. I got two NRF52840 DK. Got to install both Segger...
Hello all,
I have a question about nRF52832.
What I want to do is increase a number every 20 micro seconds.
In other words, count how much time has passed .
(ex...
I’m developing a wireless sensor based on MINEW nRF52832 modules.
I use SDK 16 and SEGGER embedded studio.
The target is powered by a 3.6V Lithium Thionil battery via...
Hello,
I have been trying to setup timer counter for nrf9160dk using the sample I have attached but for some reason the timer value is always read as 0. Not sure if the...
Hi
We are thinking about migrating a project to the nRF52805. One of our concerns was that the nRF52805 may have no "legacy" UART and only supports the UARTE, which is much...
Hey There,
The problem I have is the following:
I am able to open a Port via Putty and C# Script. I set it up like I found it in the docs. ( https://developer.nordicsemi...
Greetings,
If I send empty line (CR or CRLF) to the modem AT port, modem freezes.
Firmware version: 1.2.1
AT%SHORTSWVER %SHORTSWVER: nrf9160_1.2.1 OK
User application...
Hi,
I have developed succesfully an HTTPs client but I am facing a problem related to a relatively long response from the server when I issue a GET request. After the GET...
Hi,
When I try to update the modem firmware I get this error Errorcode: CouldNotCallFunction (0x9) Lowlever error: Unknown value (ffffff24). See attached picture bellow...
I have a issue with nrf21540 in the Transmit state after the Receive state with using of GPIO for control Transmit / Receive switch.
I'm doing next steps for reproducing...
Hi,
I am trying to use the thingy91 to publish some sensor data to an Azure IoT Hub, I've tried to look at mqtt_simple and modified "asset_tracker" application but I couldn...
Hi Team,
This Query is regarding HF frequency Crystal settings, how to configure the nRF52840 Evaluation board to different frequencies. Actually we need to test the crypto...
Hi there,
I'm attempting to link in a static library archive to my nRF52840 targeted project and receive the following error: Exception table sections and plain sections...
when I use Jlink viewer for tracing, found a fatal error:
1 code:
static void lfclk_config(void) { uint32_t err_code; NRF_LOG_INFO("enter lfclk_config"); err_code = nrf_drv_clock_init...
