Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
SDK： nRF5_SDK_11.0.0
Softdevice： s132_nrf52_2.0.0_softdevice
chip:nRF52832
In debug mode, I found through the disassembly window that the program stopped every time...
Hi Guys,
I'm currently developing an app using BLE nrf18522 development beacons.
So I just bought 10 and did a test in a big park with the beacon Tx set to -60dBm and...
Hi, the latest version of SDK is 14.x.x, by principle I should be using the latest, except by going through the SDK14 folders I get the impression that it is exclusively for...
Hello,
This is related to using Seger embedded studio on a mac for thingy52.
With all the amazing help from this forum, I am trying to compile and upload FW onto thingy...
Can we send scan response packet with advertising packet in non-connectable mode? I have taken eddystone beacon example given in SDK 12.3.0 and s130. My beacon has to advertise...
Hey guys,
I'm just being very lazy today and I just skimmed the datasheet for <nRF52832_PS_v1.0.pdf> but didn't manage to find if there are any "pin-muxing" limitations...
Yet another app_uart_fifo question.
I'm using SDK 11 with uVision.
It is my expectation that, if using HW flow control and a FIFO to RX, no received characters should be...
I am writing drivers for external ADC and I need to write my own SPIM driver using hal of NRF52 SPIM. However, after trying for a day I am not able to see my waveform in my...
Hi,
I am using ble_app_blinky_c_pca10040_s132 project, but I found it cannot output log, by using NRF_LOG_INFO. I have tried some ways, but it didn't work. I need your help...
Hi,
I'm in the process of porting code from a PCA10000 rev2 board to a custom board, using the ISP130301 integrated MCU (contains a rev3 nrf51822 IC). I'm using nrf51 SDK...
Hello,
I'm using a modified version of the serial example of the SDK 13.0.0 with a PCA10056.
The modification are that i use nrf_serial_read in non-blocking mode (timeout...
I am using SD132 V5 and SDK 14.1
I found the sd_ble_gatts_characteristic_add() is being used in most of the example projects, but I suddenly found the characteristic_add...
I have nRF52 on both central and peripheral. I'm getting the RSSI value on the central by looking at the RSSI field in the ADV_REPORT event. I see the RSSI values has a wide...
