Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi,
I made a DFU procedure with:
nRF52840 DK as Disrtibutor
nRF52840 Dongle as Target
Since composition data of my new firmware was the same of the one allocated on...
Hi, I am developing an application to read the ADXL355 via SPI. I have not been able to read the register of my accelerometer. And I don't know why. I tried reading the register...
Hi, I'm getting an error saying that "ble_link_ctx_manager.h: No such file or directory issue"
This is the main.c file:
Also, I have attached the snapshot of my project...
Hi!
I'm developing for nrf52832 using zephyr. I'm using the nordic hal driver in order to use the PWM with EasyDMA. The PWM is used to control a piezo buzzer. The PWM is...
I have very advanced project based on nrf52840dk for dev and custom boards for prod.
The development environment is based on zephyr build dockers. Zephyr is 3.5.0.
I would...
Hi,
I am having a hard time for days now trying to get the MCP2518FD working on a nRF9160-DK board. This device, embedding CAN transceiver and receiver, is accessible through...
Hello ,
I have a few questions about the connectivity bridge on T h i n g y : 9 1 . I 'm currently working with Bluetooth data on the nRF52 SoC and I need to transfer it...
I am building both the IOS and Android version of nRF Connect Device Manager and I am able to bootload/update my application.....but
But, we have external memory and we...
Hi there,
I want to manage certain devices that have an address and a value. I would like to dynamically add and remove devices from my data structure. I believe that using...
nRF52840-Preview-DK LED5 is off, J-Link Error.
I press IF BOOT/RESET key then poweron the PDK, no BOOTLOADER removable disk drive letter appears, I have installed the driver...
Hi all,
I am developing a sidewlk application as a replacement for LoRaWAN recently based on the sidewalk protocol implemented in the nRF connect SDK. I would like to check...
Hello,
We are currently manufacturing products using the nRF52840 with the nRF5 SDK. We are planning to develop new products using the nRF Connect SDK and are currently...
below is my develop environment .
TOOL : VSC - NRF CONNECT SDK 2.6.99 DEV : NRF7002DK
I am currently looking into the BLE GATT structure in NCS.
Since I need to use...
1. am currently using the nrf9161_dk. and have not modified the modem FW in anyway.
2. I am using the vscode extension provided by nordic to build/run this sample
a, i...
Hello, I am trying to migrate from v2.5.0 to v2.6.0. I had subghz working for the sidewalk samples in v2.5.0 but can't seem to get it working in v2.6.0. I don't see any errors...
