I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
I am working on nRF5340 DK Here Blinky sample program in running successfully LED is blinking. while running HELLO WORLD sample program its shows no error but its not connecting...
Hello,
when switching from 1.8.0 to v1.9.1 release unfortunately modem delta update fails. I have also tried with v2.0.2 but without success. I am trying to update the...
I tried a few demos for the nRF5340-DK and most of them work fine. What's unclear to me is where the TX Power is configured or what the default TX Power is in the Zephyr based...
Can you provide an example of how a thread commissioned Matter device can request and retrieve data from the internet?
I understand how a Matter controller can get data...
Hi,
I'm trying to capture and communicate BLE devices on the Desktop/Laptop running Windows and MacOS.
My Application is to capture BLE packets, Connect to particular...
Hi,
I have an application project using nCS with following prj.conf file:
The issue is I am using nrf52833dk and the flash is only 512kb, my build file .bin size...
We have two products which are very much similar and have both an external RTC. So processor (nRF5340) and external RTC are identical. On one product, let's call it WP, everything...
Hi，nordic
I am using ses6.22a, the sdk is 1710 and mesh5.00. When I integrate the serial port case into the mesh sensor case, the serial port can work normally, but it must...
Hello guys, i'm attempting to record the radio_end event, and i tried to enable it with the following code:
However, the second line constantly crashes the chip.
In...
Hi:
I used the following command to install matter OTBR, but the following error occurred when executing this command;(sudo docker run -it --rm --privileged --name otbr...
hi,
I would like to purchase the following nRF-Desktop. It is a wireless BLE keyboard and mouse set.
https://www.nordicsemi.com/Products/Reference-designs/nRF-Desktop...
Hi,
I am using the nrf9160 and attempting to enable MCUBoot and secure boot. Is it correct that you still cannot use any form of TF-M with MCUBoot on the nrf53 or nrf91...
Hi,
I am currently using the NVS library with the nRF9160 and an external SPI-NOR flash device (MX25R6435F). I am getting concerned with the NVS library causing issues,...
Following Getting started with current measurements on the nRF9160 I applied the
to a Thingy:91 (disabled SERIAL, NCS-2.0.0). With that I get about 0,190 mA. That value...
