Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hi nordic
I am using the nRF54L10 and Nordic Zigbee Add-on version 1.3.0
I have probably been raising questions about polling for quite some time,
but I have not...
SUMMARY
A custom board (nRF52832, BLE Central + Peripheral roles simultaneously) reliably hits a hardware watchdog reset (RESETREAS shows WATCHDOG only, never CPU_LOCKUP...
Hello,
I have added DFU capabilities to my NRF54L15 project using:
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU =y
and
SB_CONFIG_PARTITION_MANAGER =y
SB_CONFIG_BOOTLOADER_MCUBOOT...
Hello DevZone Community,
I wanted to share a unique hardware-in-the-loop implementation using the Power Profiler Kit II (PPK2). While the industry is heavily focused on...
I am designing an FPGA to have a SPI slave port connected to the nRF5340 SPIM4 master running at 32 MHz. But the setup and hold times for this configuration are missing from...
I have an application which is not able to talk with my gas gauge device when the TI EV2400 can. Looking at the waveforms all look the same except for the Zephyr code has...
our current network provider says that they have a restriction on their sim profile so that the mtu should be less than 1430. however things like pdn_dynamic_params_get()...
Is there a recommended way to access the USB data lines from the J3 connector of the nPM1300EK? I would like to be able to charge the battery and also provide a USB mass storage...
Hi, I am starting to get into the Nordic world and want to design my first pcb with nordic chips. I would like to get a review on my schematics and the pcb. I am mostly interested...
[Corrected 2026-09-11] This post originally attributed an MPU fault to the missing 7c4ea9a9d5. That was wrong — backporting it did not stop the fault, which looks like a separate...
Hello Nordic Support,
I need version-specific troubleshooting advice for an nRF52840 DK, PCA10056 hardware v3.0.3 (label 2026.16), with the nRF5340 interface MCU. I have...
nPM1300 LOADSW1/LDO1 quiescent current issue — XIAO nRF54LM20A Sense
Status: unresolved as of 2026-08-27. Written to summarize the investigation for external reference ...
Hi,
I am developing firmware on the nRF93M1 DK and have a question regarding the Wi-Fi location feature. According to the Nordic documentation (Features of nRF93M1 — nRF...
