We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Hello,
I was recently trying out some samples with the nRF9160 DK and I had run into some issues when trying to run the nRF Cloud Client Application .
I had flashed...
Hi,
I'm developing on the nRF52 DK which has the nRF52832 chip.
I have a small vibration motor which I'd like to control on/off through one of the boards GPIO pins. At...
Hi,
I'm trying to modify the light bulb example and turn it into a light switch (not a light switch that controls another bulb in the network), but I'm quite new on the...
Hi,
I've noticed that there was an issue with ble_nus in SDK 15.3 - detailed in this post .
I'm using SDK 17, and in my application, I don't check data_handler != NULL...
Hi. I am using nrf52840 with Softdevice 16.0.0.
I set the maximum size to 247 bytes. But I probably only need 68 bytes per packet.
Should I reduce my MTU size to 71 or...
Hi everybody!
I'm currently working on some firmware updates for a motion sensor. The code was originally developed with SDK15.0. The setup is as following:
NRF52840...
Hi,
I was trying with the aws_fota sample, I follow the instruction here and download the app_update.bin with no problem. After it shows completed in 100%, device reboot...
Hi,
I am measuring the time taken between an ANT application sending a message, and a receiving ANT application generating an EVENT_RX. This time is being measured using...
Hi,
my environment:
nrf5340 dk
nrf connect sdk - 1.5.0 version
segger studio IDE
we need a provisioner to add node into the BLE mesh. As per my knowledge, we...
Hi,
I have a few questions about how the peer list works. (using S132 v 7.0.1 and SDK version 16)
How or when are peers added to the peer list of the Central? Are they...
Hi Experts, I have a short quastion, what is the minimal RX-RX turnaround time of nRF5340? Unfortunately this parameter is not available in the specification any more. For...
Hi , i try to translate the arduino library using this URL github.com/.../src
to manipulate the spo2 oxygen concentrator value using the max30105 sensor I try to configure...
When I set tx_power and paired with the following microcontrollers, the power consumption of the 4dbm setting became larger than that of the 0dbm setting. Is this an effect...
Hi,
I am currently working on SDK 15.2.0 on my NRF52840 DK to program a bootloader that can do DFUs over SPI. I have been following the protocol found in this link . I have...
