I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
I am trying to merge the following projects:
SDK versions: 17.0.2 and 5.0
I have taken the contents of the mesh example sensor/server and merged it into the ble_blinky_example...
I created .c file, and add a few TWI functions to it. However, when I run the code in segger, all functions in the .c file shows a "multiple definitions of xxxx" error (see...
Hi!
I am working on an AoA project and I am using nRF Connect SDK. For the transmitter part I saw that sample application is already written and for receiving part it is...
Hi,
Our entire board is running around a nRF52832. Recently it has been difficult to find some of these SOC. Is it safe to replace it with the nRF52811 without changing...
Hi,
I am trying to compile ble_advertising.c file for a specific application based on nrf52840 and I am getting the following error:
nRF5_SDK_15.3.0_59ac345/components...
I am working with an nRF52840 on a custom board. Our device has a number of sensor attached in various ways including spim, twim, uart. I've used the ble_app_blinky as a starting...
Hi Dev Team,
I am enhancing my Thingy91 application using the mqtt_simple sample and NCS v1.5.0. I am basically connecting to the MQTT broker, sending data and then disconnecting...
I am using nrf52840 as PTX and nrf24l01+ as PRX. The application I am working on requires me to send 30 bytes from PTX to PRX at a 2 kHz packet rate. If both devices are near...
I am trying to make ble communication work with I2C but i cant make it work i dont understand what is the issue the code is being build but it does not advertise can someone...
I'm building a firmware for nRF52 which is using app timer v2 with RTC1. After a while, app_timer starts running many times faster than normal, and I'm not sure why. Nothing...
I use pc-ble-driver to control nRF52840 dongle. I want to speed up scanning of advertising time.
So I change SCAN_INTERVAL and SCAN_WINDOW.
How can I modify the parameters...
The enocean_switch example has MESH-config example, to store data in FLASH, within the mesh rules.
I use it in my app, IT WORKS, but the biggest data array what I can store...
hello folk,
I am working on nrf52840, I want it to assign Static UID of any kind that even won't change after the device gets reset.
I have already gone through "FICR...
Hi,
I am looking at using the nrf5340/nrf9160 in a device. In this device, I need to have high endurance storage of some data that must be kept secret, integrity checked...
