hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
I want to edit the sample source (nRF5340 Audio) and program it on my own board. The connection is CIS. I am using NCS version 2.5.0.
I want to set the I2S clock as follows...
sdk-nrf: v2.7.0
When PAWR is enabled I no longer get connection timeouts as a callback to bt_conn_cb.connected with the conn_err parameter set when attempting to open...
I tried the following settings to output 12.288MHz I2S MCLK with nRF5340 Audio, but it did not work as expected.
The I2S settings I want to output are as follows.
MCLK...
I am currently writing sniffer firmware to the nRF52840 and am trying to check Thread communication using WireShark.
When I displayed the RSS, I got the value shown in the...
1. Hi i am utilizing nrf52840 sdk with ver 17.1.10 s140 and i have the central UART as main app from there we are calling bootloader
2. Before calling bootloader ble dfu...
Hi,
I am just starting to develop a nRF5340 based prototype. I am using the openthread CLI example as the first step. I have configured the device tree to suit our board...
Hi,
I'm looking to send short data from my mobile phone to the nRF5340 via NFC. I've been searching for examples in SDK 2.7.0 but haven't found a suitable one yet. Now,...
Hello. We recently started working with the new nrf connect sdk and we need to implement a very simple bootloader that would only jump to the main application at a specific...
Hi there,
I have a project developed in SES, using nRF5 SDK v15.3.0 with only Just Works security without using LESC running on nRF52840. It has been running fine for 2...
In our custom board we checked WIFI, facing below issues, 1. We flashed sta sample project to our custom board facing the issue below. Is there any configuration needed to...
Hello! I am working on nrf52840 NCS 2.6.0v I Configured the button to generate an interrupt every time it is pressed. Then, inside the interrupt handler (callback function...
I am using Asynchronous API of uart to receive the data. During the reception I face UART_ERROR_FRAMING issue in UART_RX_STOP event. But after getting that too it enables...
I use the nRF52840 development kit. In this Board i flashed the ncs zephyr sdk v2.6.0 sample code for system off and device going to sleep.
i Want to wakeup the board from...