Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi,
I am just staring my evaluation with nRF9160-DK. The video says I need to turn the dev board on, insert SIM card and wait for LED3 and LED4 to light before proceeding...
Hello,
My firmware is based on the ble_peripheral_HID_mouse (nrf52 DK, pca10040e_s112). I receive unexpected BLE_GATTC_EVT_HVX events of indication type from Client side...
Hello, I am using nrf52840 dongle for development purpose whether there is any provision to generate the code which is used by nrf connect for desktop from the app or by any...
Hello, everyone.
I'm dealing with an example of a sensor in SDK v14. I've checked it's working and now I'm going to put it in the code I made in SDK v17.
Code must be...
What happened to SDK 7.0.0
It is no longer available for download.
I assume some problem was discovered, so it should not be used any longer, at all?
Any help a...
Hello,
For clarification I use the nrf5_SDK_for_Mesh_v2.1.1. and the nrf52832.
I'm trying to scan for Ibeacons in which I need to get the UUID, major, minor, and the device...
Hello,
I have intention to use NRF52840 as HW peripheral just for communications over BLE. It means, it will be connected to the main MCU and provide interface for utilizing...
I am using nRF52840 Dev kit (PCA10056) , with nRF Mesh SDK 4.0 and nRF SDK 16.0 .
I have such FOUR kits . I have been able to modify vendor model for a sensor to transfer...
Hello everyone.
I'm a fresher of programming nRF52833. I'm doing an application for my final project in my university. What I need is get the RSSI in order to analyse the...
Hello -
I am evaluating nRF52840 to replace the Bluegiga BLED112 in an older product. I am surprised to get very low range from the nRF52850 USB dongle, barely 10-15 feet...
Hi, NordicTeam
Nrf52805 as slave and mobile phone as master to connect slave. NRF_SDH_BLE_GATT_MAX_MTU_SIZE = 247, MTU = 23, the master sends the Prepare Write Request to...
Hi,
I'm developping a new application where the device normally is in low power (waiting button with an interrupt)
while(!gIsButtonSwitched) { __WFE(); }
the consumption...
Hi everyone. I have an application using BLE and OpenThread dynamicaly. I am working with nRF52840 chip with nRF5 SDK for Thread and Zigbee v4.1.0 (Release Date: Week 18,...
Hello, I am using the Zigbee CLI Agent as coordinator, and when a router device or end device joins the network I want to configure attribute reporting.
I am able to configure...
We are running a trial in an open field, where we connect NRF52840 ( GW ) to an NRF 52833 (Node ).
Distance between the units is around 80 meter , we are using Coded Phy...
