Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
Does anyone know of a good starting point for Bosch BHI360 IMU integration into nrf5340 and Zephyr?
Did look at: https://community.bosch-sensortec.com/mems-sensors-forum...
Hi,nrf52832 entered in bootloader mode.as ld5 led is keep blinking on power reset and holding if boot/reset button.please help me to get board back to normal mode.thanks.
I had previously gotten working code to communicate with my SPI device on the nRF5340DK w/ NCS v2.5.0 that uses the HAL SPI library inside TF-M. I used NCS v2.5.0 (nrf\samples...
I observed another user having this same issue with resolution.
It appears the watchdog configuration has changed but I'm unable to track down the driver/overlay/etc that...
Hello,
I am working on an nRF5340-based project where I successfully integrated the broadcast_source and central_and_peripheral_hr examples from SDK 2.6.0. Both functionalities...
Hello all,
I'm working on a localization system using the nRF52832 chip and Bluetooth Low Energy (BLE), but I'm running into challenges due to how BLE transmits signals...
Hello Team,
We are currently working with the nRF54L05 and using the nRF Connect SDK. We have successfully evaluated basic BLE peripheral samples on the EVK.
For our application...
Hi,
I am going theough the first lesson of 'nRF Connect SDK Introduction' course, have installed nrfutil and updated the path. When trying to install 'device' as per the...
Hi, I have this problem and I couldn't find any working solutions. I am developing my own hardware and there weren't any problems until I started to use debugger. My program...
Is there any reference information on how long (in ms) different steps in a BLE pairing process takes? e.g. Pairing Feature Exchange, Short Term Key Generation, Long Term...
Hi all, In my project i'm using the nrf52840 SoC in my board. I'm currently working on the bootloader, and I would like to add additional logic to functions mentiond in the...
Hi,
I am trying to train a few beginner FW engineers on RTOS concepts and have been using the Nordic training videos. However, sometimes, its tough to explain thread execution...
Hello,
I need to persist ~200K of data on the internal flash of an NRF52832 chip. I've run a memory report and I'm current taking up 185Kb and the chip has 512 Kb of flash...
Our project has been working on nRF21540 & nRF52833.
Let us have a method to reduce the power of nRF21540 under 400uA at idle.
Currently, without nRF21540, the power...
We started a new project using nRF Connect SDK & Zephyr. Installation of development tools is very easy and convenient using VSC add-ons. However, we are concerned about the...
