I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hello Everyone,
I want to start working on nRF51822 development kit for my project. but as mentioned on this site : www.nordicsemi.com/.../nRF51822-Development-Kit
that...
Hello there,
I am using the experimental_ble_app_uart with S110 on nRF51-dk and receiving sensor data via 1MHz SPI every time the timer ticks = 100ms.
Data transfer displayed...
Hey,
I created a custom PCB with the nrf51822 that reads two sensors via TWI and transmits certain data over BLE. I can program the chip, print strings to the terminal...
I am having problems with th Master Control Panel (no response from master emulator). When I search devzone, I see an answer related to this question that says cloed because...
Hi,
I have application where I drive LEDs with shift registers. I need to send 14 bytes via SPI every 200us while I am in BLE connection. Timing should be exact as shift...
Hi,
I have a project where I need to communicate using UART BLE between nRF51822 and a PC (MS Surface Pro 3) with Windows 8.1 and embedded BLE hardware.
I have programmed...
Hi,
I have downloaded nRF51_SDK_7.0.1_1d6e5cb.zip and run nRF51_mdk_6_1_0_installer.msi
Neither zip file nor created Nordic Semiconductor/nrf51/ folders have ewp or icf...
Hi,
I think it's a simple question. I want to connect a micro to communicate with a phone via the nrf8001. I ported everything thanks to the guide that you posted (for...
Can we use the tx_complete.count given with BLE_EVT_TX_COMPLETE as an indication on how many packets were sent out from the last ended connection interval?
thank you
...
I have a custom board utilizing an RF51822aa device. To test connectivity to the board I built blinky_s110_pca10028. Using Keil 5.12 I tried to debug the program simply expecting...
I am using custom nrf51822 board. I am trying to debug through JTAG(segger j-link). While downloading the program into flash, I am getting error like "Error: Flash Download...
where can I get working sample code of nrf51822 with nrf24l01
including code of nrf51822, and code of nrf24l01, both TX, and RX.
in my application, I need 518 to RX data...
I am working with a university project where need to connect up to 20 wireless sensors together with 1 master, which will be communicating with either a computer or smartphone...
I found a IAR project at dir [nRF51 SDK_v4.4.1.31827\Nordic\nrf51822\Board\nrf6310\ble\ble_app_hrs\iar].
But my IAR ARM IDE(ver 6.60 newest) don't support nRF51822.
Do...