Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi,
I am trying to connect 4 devices (2 nrf devices + 2 B24 custom modules). Each of them can get connected independently as single device, but as soon as I start connecting...
I'm reading the code of peripheral_hids_mouse project and I want to select some functions to fill my own code.
prj.conf has these two config:
CONFIG_BT_GATT_UUID16_POOL_SIZE...
Hi,
I followed SDK 2.7.0 Fast Pairing example and successfully downlowd to nRF52840 PCA10056 EV board, using VS Code nRF Connect Extension.
Fast Pairing Input Device example...
Hi,
I am hoping to send/receive binary data (a protocol) on the same UART that has logging/shell enabled. Is there a way to access the UART RX traffic that the shell gets...
Hi all!
I've been working on a project using the nRF Connect extension for VS Code and I've been trying to figure out which HEX file in my build/zephyr folder for my application...
Hi,
I am sending a SCAN_REQ packet from my code after receiving an Advertising packet from the NRF5340 DUT. Sometimes I receive the SCAN_RSP packet, but other times I encounter...
I am working on a project where my hardware includes an array of LEDs. I want to run an LED pattern on the array during the DFU process. I have tried to find a solution for...
Hi, I have been working with I2S Mic sph0645lm4h-b and nRF5340 audio DK. I configured mic and while I'm reading the data it throughs an error code of -5. I'm Sharing the code...
I am a beginner and I want to switch from SDK 17 to nRF connect SDK v2.6.0, but I found that many configurations are different, such as gap initialization, gatt initialization...
Hi,
In my wearable application, I would like to have reset functionality by pressing two buttons, which I also would like to use as application interrupts. I read that the...
I'm working on implementing asynchronous UART on a nRF52840dk but uart_callback_set() is returning -88 (ENOSYS), which according to the tutorial here means it's not supported...
Hello!
I am using a nRF52840 board for some really simple development. First I just tried to run the blinky example and connected with another BT device. It worked well...
I attempted to use https://github.com/Protocentral/protocentral_max30001_zephyr_driver to build my project. However, I am still encountering some issues.
1.In the overlay...
Was following steps here to set up the sidewalk sdk from a blank nRF Connect SDK for VS Code application template using sdk v2.7.0. I noticed immediately that the directory...
Description : I am experiencing a build issue after porting my project from nRF SDK 2.4.2 to nRF SDK 2.7.0. The project involves using the nRF5340 and was building successfully...
