void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi there.
Right now, I'm facing the issue that I want to use the camera OV7670 with the nRF52833.
I don't know how to start or what example I can take as a base to start...
Hi,
I am using EVB of RAYTAC MDBT50Q-DB (nrf52840 module) for power consumption testing,
I'm running a zephyr application on it, to debug power consumption issues, using...
I have an application where I would like to use ACLK at 12.0 MHz to drive the I2S MCLK signal and create an atypical audio sampling rate (46875 samples/sec). If ACLK is at...
Hello!
Using SDK v2.6.1 and the nRF5340 Audio application, I want to use an external button as button5 instead of the one that is on the board.
I noticed that if i change...
Sometimes I just want to compile a single file for an nRF Connect project with VS Code and the nRF Connect extension. This sometimes fails because an include file isn't found...
Hi.
I am updating an nrf9160 B1 project on a custom board in SDK 2.1.0 to SDK 2.5.3, and I am running into a problem when building. This error does not show up when building...
Hi,
Hello, I have a project that's working great but now I want to extend the abilities of the device by using the extended PHYs. I know there are a so many threads on this...
Hi DevZone!
I'm currently developing a device that has several hardware actuators and I've implemented 2 OnOff Models each belonging to an element. But right now I'm having...
Hello there!
I'm trying to enable secure boot via CONFIG_SECURE_BOOT and am currently getting the following error:
I'm using zephyr via sdk-nrf v2.6.1
Searching the...
Hi,
I just try to use the DFU over USB to upgrade the FW but i found one problem which is the process will erase the external flash data
but i put the some sensor FW data...
I'm upgrading from SDK version v2.4 to v2.7 which introduces the new Zephyr hardware model and I'm struggling with the transition. I have two custom revisions is based off...
Hello,
I am using nrf7002dk on NCS version 2.6.0.
I want to send data to an HTTPS web server using WiFi.
I saw some mentions about HTTPS in several posts on Devzone...
HW/SW Versions:
nrf52840 Dongle DK
nrf Connect SDK 2.5.2
Issue:
I'm developing a Zigbee device based on the ZBOSS, using an nrf52840 dongle development kit and there...
Hi,
We have developed a nrf5340 custom board powered 1.8 V. So we cannot use the nordic DK board to program it.
I would like to know if there is an interface other than...
I have an application where I am using the SAADC to take ADC samples. At any point during the measurements, I want to be able to stop the samples prior to the ADC buffer filling...
