void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi there,
I must interact with an I2C slave that sends variable-length messages. The first byte of the transactions describes the length of the remaining bytes.
i2c_write_read_cb...
Dear Support,
we would like to know what is the total value of the capacitance and the inductance of the nRF52805 (for ATEX certification). I can not find this information...
We have project using the common Matter Code base from SDK 1.6.1 and using a variation of the code to act as a switch sensor device time. This seems to work pretty well; however...
I need to add tx power to my BLE advertising, but I need to ensure it is in the Scan Response only not the main AD PDU.
Also, I change the Tx power by code using the function...
I have a PCB made for my project. I want to read log from RTT. When I try the same software in the development kit, I can read from RTT. But when I want to read from the PCB...
Hi,
I have a proyect with the following memory requirements.
The current project has a propietary bootloader and bare-metal application. Therefore there is no Zephyr...
Hallo,
In the BSP startup files for the nRF5340 (gcc_startup_nrf5340_application.S & gcc_startup_nrf5340_network.S) the interrupt vectors USPTn_IRQHandler (n=0,...,3) are...
I hope someone can help me here with my question.
In my project we are using a nrf9160 with modem fw version 1.3.5. The application sends/receives data periodically (1 hour...
Hello and thanks for reading.
I have a critical problem with my device, and seeing as the problem is BLE related I figured I would ask your help as well. We are using the...
I'm using an nRF9160-DK board with the provided iBASIS SIM card. I followed the instructions here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.4.0/nrf/working_with_nrf...
Hi, I have a problem related to DFU OTA through BLE
When performing OTA through Bluetooth, I encountered the following issue:
Firmware built in the same build can be successfully...
Hello, I started looking into the DPPI from NRF5340 series and planning to integrate some functionality into an existing zephyr-based project. Specifically, I need timer-based...
Hey team,
We're having trouble with our device. It's been working fine, sending messages to our backend without a hitch. But after a while, it starts having problems connecting...
Hello.
The MCU of our new design will be the nRF52832.
I would like to know if it is ok to read the voltage of the battery that powers the system, nominal voltage of 3...
Dear support team,
1. Can mesh provisioner configure multiple devices at one time? For example, there are five unprovisioned devices within the provisioner's network. Can...
