I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
To make sure that the nRF52840 SoC is not powered when the nRF power switch (SW8) is OFF.
So what happens if I power the nRF52840 SoC when the nRF switch (SW8) is ON ?
Hi ,
When i run samples/keys/hw_unique_key app and select nrf9160dk_nrf9160_ns board . The app can not run into main function instead run into system_halt.
__WEAK...
Please provide the part number(s) of low-cost NORDIC processors that have a quadrature decoder and a PWM.
We are working on an application that is using a Nordic nRF52840...
Hi,
During the validation of our device, we found that the RTC (synthesized from HFCLK) was quite a bit off. Instead of the expected 32.768kHz, we measured 33.047kHz.
...
Hi, I am using urf52832 ( also have 52833 dk).
I am trying to use another pin us uart, which tx is 29 rx is 30 define in project_pinconfig.h.
But I can't see any uart...
Hello, I'm working with BLE Mesh using NRF52840
- Our setup: NRF-Connect-SDK 2.1.0
- Summary of our project.
+ Provisioner node to control lightness for all nodes in...
Hi,
I'm having an issue including USB DFU Trigger library in my prototype application running on nRF52833.
My application is based on the ble_uart example, to which I...
Hi,
My application is written on top of freertos ble example. I need to integrate radio test example as well for certification. I am running into errors when I try to...
Hello,
my first Post here, so i hope i do it correctly.
I have the following Problem with the Configuration and Communication over TWI/I2C.
The Voltage of the TWI...
I am working on BLE on NRF52840 using soft devices for BLE and I was using sd_ble_gap_ppcp_set API to set the connections parameters for the BLE so I think the PPCP is the...
I'm calling this function from a Zepyhr project:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/connectivity/bluetooth/api/gap.html#group__bt__gap_1gad2e3caef88d52d720e8e4d21df767b02...
Hi, I am trying to test multi_sensor example from Zigbee and Thread SDK 4.2 using official Nordic nrf52840DK with few Zigbee hubs. Example is located in \examples\zigbee\experimental...
