Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I change nRF52832 firmware to support DFU OTA. But ble_dfu_buttonless_async_svci_init() failed with errCode=0x4.
0> <info> app: Version 1.2.1 0> 0> <info> app: ========...
When I use Keil to build project for supporting DFU OTA. Keil shows changing *.o to *1.o. Is it normal?
Build started: Project: ble_app_band_v4 *** Using Compiler 'V5.06...
We are using the Softdevice controller from the nRF Connect SDK on the nrf5340 processor and have implemented the commands to read and set the tx power level in the controller...
I want to take readings from SHTC3 temperature and humidity sensor from a custom board. Using I2C master as nrf5340 how can I take readings from slave custom board. Please...
Hi guys.
With the nRF52840 DK(PCA10056) running the Running Speed and Cadence Service (RSCS) example, the nRF Connect app on my Galaxy S10/Android 12 was able to scan the...
For emission testing, we need to be able to use some DTM commands (such as: transmitter test) inside our normal firmware.
The normal firmware uses the softdevice for BLE...
My project requires two sensors to operate on the same i2c bus, one of which is a display and the other of which is a touch sensor. And I have a problem where, if I test both...
Hi Everyone,
We are using nrf51824 for our project. As segger embedded studio has free license we have to migrate Keil project by following the article Segger Embedded Studio...
I have vsc version 1.66. I'm getting the following notification:
File changes watcher stopped unexpectedly. A reload of the window may enable the watcher again unless...
Hello,
I am using the https_client example for Thingy91. Everything was working fine until I tried to change the website to send https requests to (from example.com to google...
Hello Team Nordic, May I ask for your advice on how to build one nRF52840 to have two different UART connections to two different devices? May I ask for the any code examples...
Hi,
I am trying to integrate custom protobufs into the asset tracker project. I am referencing the zephyr/samples/modules/nanopb project for the same.
But I am getting...
HI ,
I'm trying to open terminal/command SDK v2.0.0 from toolchain manager (working with nrf connect for desktop v3.11.1) but it doesn't open.
while on SDK v1.9...
