here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi, I'm developing an application using fds. I merged fds into ble_app_uart and built complete But when program run fds_init() nRF was crashed I called fds_registered before...
I am using NCS 1.7.0 and latest nRF5340 DK
I am trying to update netcore firmware using the process defined here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1...
Hi everyone!
I have a question regarding the audio support on the nRF52833 chip. Is there any support for sending audio ( Low quality compressed audio ) to headset? Or...
Hi everybody.
For a personal project, I need to integrate a flash or a microSD card to store data.
As computation core I want to use nRF52811, but I'm not able to find...
Hi,
I've lost hours to this so grateful for your support!
I have a custom board using Raytac MDBT42Q, which has a 32MHz clock in the module and I'm not using an external...
To whom it ma concern,
we observed Unkwon Resets after Long runtime ; Several Hours.
We use the NRF52840.
After the reset bit 1 in RESETREAS is detected .
BUT investigation...
My project is based on 'ble_app_uart' and I added dfu service..
so there's two custom 128bit uuid in my project..
But before this, I only want to test dfu service mode...
Hi,
We have made an app that gathers GPS coordinates using an external antenna with the thingy91. The problem we have is that we struggle to test the code when we don't...
Hello,
I am using the nRF52840 dongle with the nrf sniffer 4.1 firmware running on it, using Wireshark to read out its results.
This works fine for advertisement packets...
Hi!
In my application, I am receiving A-GPS data from nRF Cloud. After the data is received there is a considerable amount of time where the GNSS module is blocked because...
Hi,
I am looking into the example of SAADC and sending data through BLE. My tests are based on this example: github.com/.../ble_app_uart__saadc_timer_driven__scan_mode...
Hello,
I have been working on a project that uses nrf52832 custom board. Recently, I have been trying to implement device bonding and realized that the data transfer rate...
Hello All,
Hoping this one is an easy one - have an image for the nRF9160-DK - it hangs unless I make a serial port connection - so, apparently - printk() is blocking waiting...
I like to use nRF52840 now instead of nRF82833 which was used during the CE-RED compliance test. I only like to change the nRF chip. All other components at the PCB will stay...
