here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hello.
I want to write 3 bytes of data using BLE in a memory area that will not disappear when the nRF52820 is powered off or reset.
Currently, when I create a program...
Hi, I trying to run the spi_flash example form zephyr.
My sdk in 1.9.1 - nrf52840 in a custom board.
I have tried everything and I always get the same result:
JEDEC...
Hello,
Aim : To write and read x bytes from the QSPI interfaced external PSRAM(APS6404L-3SQR) using the nRf52840.
Configuration : Following is the configuration of the...
Dear support
I am developing a generic central application intended to connect any BLE devices which is connectable. So I need to figure out which parameters are needed...
hello Nordic
i am working with nrf52832, ncs 1.7.1
we have to turn on the power before trying to read jedec and to avooide changing ncs spi_nor or using SYS_INIT we decided...
Dear Nordic-Support Team,
Introduction
I have read through some sources (tickets and documentation) but I am still struggling to see the big picture of UART configuration...
SoftDevice: S113 v7.0.1
SDK: 15
Chip: nRF52840
It looks like setting PA/LNA pins on port 1 result in NRF_ERROR_INVALID_PARAM being returned by sd_ble_opt_set(). When...
Hi All,
We have been using NRF52 products for a few years now and currently doing an PoC of using the BLE DFU with a CODED_PHY.
Our solution does use the DFU already but...
I am using the nrf_serial library SDK 15.2.0. I have implemented the solution suggested in Case ID: 216973 for recovering from driver errors. This helped me get over errors...
Hello,
been trying to add lte_lc_connect_async(lte_handler) to mqtt_simple, just like the way it is in sample aws_iot. Instead getting a failed response.
Now not sure...
Hello Team Nordic,
Greetings of the day!!
We are currently testing the current of our device with the PPK2 kit.
We use the ESP32 as MCU and we are switching Cellular...
Hi,
I recently added the DEBUG_NRF preprocessor definition to my project because I wanted to use the nrf_assert module in some of my files. Now my project is crashing a...
In the nRF52840, I used the app_usbd_cdc_acm_write(&m_app_cdc_acm,tx_buf,size) method to output the data.
At the beginning, I use the pyserial to read the output data...
Hi,
I'm developing a software in python 3.9.6 64-bit which program a nRF9160 and nRF52840 using pynrfjprog.
The software is working from vscode debug session. But when...
