I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
For Errata 149 on nRF52832 , TWIM send illegal pulse after clock stretching.
When using TWIS as slave device and TWIS require clock stretching,
Do they work correctly...
I have an issue with DFU via USB CDC ACM.
I would like to update the firmware using open bootloader over USB without softdevice.
I already tried to follow the thread:...
Hello,
I have a firmware working perfect with nRF52832 DK and nRF52840 DK, using SES 5.40a.
Now I just upgraded SES to version 5.70a. With new SES version, each time I...
Hi,
we are getting during NB-IoT attach (full AT dialogue below) for some nRF9160 SIPs:
URC: +CNEC_ESM: 29,0 URC: +CNEC_EMM: 19 URC: +CEREG: 2,"B414","000F6E21",9,0,19...
Hello,
I follow up this documentation https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/nrf/ug_thingy91_gsg.html#updating-firmware-through-external-debug-probe...
I try to run asset_tracker and asset_tracker_v2 on nRF9160DK. I observed that the default cloud Host Name is Amazonaws.com, which is shown in autoconfig.h file. see the image...
I tried to debug Asset_tracker_v2. During step by step debug, the program navigate to that part which is not included .. see the image. Also, I want to know, little more:...
Hello Devzone Community,
My name is Ted, and I am some way along development of Zephyr based firmware, running on an nRF9160 based custom board. I'm looking to put the board...
Hi,
How can we prove that the A-GPS is working correctly? We have run an experiment where we have use a module with A-GPS and one without and they have very similar (and...
Setup -
1. Sample used - nrf/samples/nrf9160/lte_ble_gateway
2. Board used to build - nrf9160dk_nrf9160_ns
3. NCS version 1.9.1
Steps performed -
1. Built the...
Hello Everyone,
I am trying to implement one wire protocol for interfacing MAX17211 fuel guage IC with NRF52840. I wand to know if there is any one wire library or any example...
Hi,
Do you have a suggestion for a 2.4GHz chip antenna? I sent a board to Ketil for RF tuning but the meander antenna ended up as too short. We would like to avoid a separate...
Hi there, I have been always using the dev board BLE antenna for the nRF52832-QFAB.. but now i need to reduce much more the size of the board, so i need a much smaller antenna...
