void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi, I'm following the steps on https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_gsg_ncs%2FUG%2Fgsg%2Ffirst_test.html
But in Programmer, the read, write, erase&write...
Creating a second advertising set with bt_le_ext_adv_create will generate an error -12.
Using nRF Connect SDK v1.8.0
The second advertising set is use for FOTA update...
Hi all,
i'am using nrf_Connect_sdk when i write this api
device_set_power_state(); it gives me undefined symbol
i enable CONFIG_TICKLESS_IDLE =y in prj.conf it gives...
Hello,
My company is evaluating the Thingy:91, we're interested in Multicell location lookups. My question is regarding the SDK, specifically if it's possible to configure...
Hi, I am unable to download my program and there's no detailed error messages, if any at all. Can someone please tell me what's going on?
Load "C:\\projects\...\\nrf52832_xxaa...
My company is creating a custom board using the 9160 and 52840. I have a BLE app running on a nrF52840 board that I want to port to the 52840 on the 9160 custom board. And...
I'm a newbie (few weeks) with nRF9160-DK and using nRF Connect SDK v1.7.1 / VS Code on a Windows 10 PC
Good afternoon,
I'm struggling with how to set up and start the...
Setup:
- nRF52832 , Softdevice s132, gcc
- iPhone is the peripheral. A custom service is implemented **on** the iPhone.
On the nRF:
- `#define NRF_SDH_BLE_VS_UUID_COUNT...
Hello.
We are developing using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral.
I am creating a function to connect to a central device, have the characteristic set...
Hi,
I am flashing Blinky led hex file on the flash at 0x5E000 location.
And again if i try to flash the different Blinky hex file at the same location. it wasn't working...
Hello,
I could use some guidance on where to look for a power draw that I am not understanding. I am not a hardware engineer but have been tasked with completing firmware...
We experienced an issue in production, in which about 40% of boards had excess current consumption by about 75uA. Root cause was found to be the PIN_CNF of a GPIO pin. During...
