here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Dear friends,
I followed the tutorial( Using serial interface for provisioning and configuration ) control a mesh node.
a) The PyACI as a host via uart connet to 52840...
I'm running NRF Mesh3.1.5 in Android on my Galaxy S10. I'm following the steps in the Bluetooth Mesh Developer Study Guide and can connect to the Switch an Light nodes as...
Hi,
I wanna my appication run first instead of bootloader. Here is my steps:
Create bootloader_setting: nrfutil settings generate --family NRF51 --application application...
Hi,
I have a card with some large capacitors in parallel with the VBAT line. How does the PPK2 work (in source mode) at board start-up where there might be a short in-rush...
I have a question. The sample code I modified is nRF52832\examples\ble_central\ble_app_uart_c. Scanning will be triggered when scan_start() is called. The device has been...
I have change the version of wireshark on windows 10 .(NOW I?M USING THE ONCE OF THE APPLICATION NOTE)
After that i have modify the .bat file because he never see python...
Hi,
My provisioner is a light switch client on a dev kit NRF52832.
Now I want to define it as a proxy node as well but I suspect that my Android App cannot send one generic...
Sorry I'm looking in the AoA.
I See that in zephyr main line there are 2 samples :direction_finding_xonnectionless_rx direction_finding_xonnectionless_ tx..
Hawe I to...
Hi,
I am trying to program new chips. I have made the following connections:
Chip J-Link ------------------------------ Gnd Gnd SWCLK SWCLK SWDIO SWDIO VDDH 5V (External...
Hello:
We have a BLE application on an NRF52840 with SD 140 and SDK 1.5.3. Our device acts as a BLE peripheral with bonding and LESC, and we additionally use block level...
Hi,
We have designed the custom PCB where 32.768 kHz crystal oscillator is required. Some how we have managed the component (MFR PART NO. TF325J32K7680 ) suggested by Nordic...
Hi, I came across a forum post that NRF51 had an issue with noises in SWCLK signal.
For the design, do I need to attach an external pull down resistor in design? If so,...
Hi good evening,
i am working on a project that requires ble transmission between 2NRF52dks and one of them is connected to a PC and apart from receiving data from another...
