void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
I want to change the BLE advertisement TX power output.
I can already do it via the prj.conf file,
CONFIG_BT_CTLR_TX_PWR_ANTENNA=-4
but I need to change it on-site during...
I am designing an ultra-low-power BLE Audio TWS board based on the nRF5340 and have followed the recommended hardware design guidelines throughout the project. This is my...
Here are results of running the bluetooth sample central uart, first when built with target nrf9160dk/nrf9160, and second with build target nrf9160dk/nrf9160/ns.
*** Booting...
Hi, I am having troubles with flashing my first code to the MDBT53V module. I am flashing via JTAG cable, from my nrf52840DK using vscode. According to my measurements the...
Hi, We currently update firmware using the official nRF Connect app with a .bin file over BLE, and that works for us.
Our team needs to implement the same DFU flow in our...
Hi,
I am facing a strange NB-IoT connectivity issue with the nRF9160 in Dammam, Saudi Arabia.
Setup
SDK version: v2.5.0
Toolchain: nRF Connect for SDK VSCode...
Hi all,
Due to wrong pin assignment on my PCB I am currently bit banging a uart on two P2 pins using the FLPR core. The read bytes and bytes to send are communicated via...
Hello,
after a longer time, I wanted to use nRF Connect for Desktop again, to figure out what exactly my device under development is advertising. I upgraded to the latest...
Back in SDK 17 or so there were code samples for both the client and server side of the LED button service.
What happened to the client/central example when you migrated...
Description
I'm working on a battery-powered application where WiFi needs to be shut down between cloud sync intervals. I'm following the same pattern as the wifi/shutdown...
Hi,
working with nRF52840 with S140 v7.2.0, not sure about SDK version. VS Code + ARM GCC + LD Gold linker.
I changed stack and heap sizes via __HEAP_SIZE and __STACK_SIZE...
We are experiencing an issue with high current consumption when using the nPM1300 powered by a battery. In Hysteretic mode, the battery current draw measures 109 µA. However...
Hello Nordic Team,
We are currently working with the nRF54LM20B device and would like to understand whether Bluetooth Channel Sounding is supported on this SoC.
Specifically...
Hi：
What is the maximum number of targets that a DFU distributor can support for simultaneous upgrade, and what is the upper limit? I haven't found any detailed explanation...
I'm trying to put my code on a RAM/ROM diet and cut out any extra cruft so it will fit in an nRF52832. It used to fit with older SDKs, but not with the newest (v3.2.3).
...
