void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
I use nRF52 DK as a central devices and i have also other nRF52 DK and use for a beacon. I would like to show my beacon's RSSI value on the UART Terminal(Realtek,Termite exc...
Hi,
I have done buttonless DFU in Custom board using NRF52832. My code with DFU is working fine in the nrf52832 Development kit. While I am trying in a custom board. My...
I'm developing for nRF52 DK
using SDK 17.02
Segger 5.10b
I'm developing a service to read pin 12 where I'll have a square wave signal of about 60Hz. When I tested my...
Hi,
Is there an example code for nRF52832 were the system is configured to operate in a certain duty cycle, e.g. performing a certain task once every 100ms, and then goes...
Hello, guys.
We want to use libuarte - advanced UARTE driver in our current application developed for nRF52840 with SDK 17.0.2.
We can successfully run libuarte example...
I'm using nRF52 DK (PCA10040) <TWI sensor> example.
On line 139, printed result = NRF_SUCCESS
However, the program doesn't print line 142. Instead, the code jumps to twi_handler...
Hi, we just found out a bug in nRF Connect for Android indicates that the phone Sony Xperia L4 supports Coded PHY. Unfortunately, when we try to run Bluetooth: Central Heart...
Hi,
I am currently trying to run the secure_bootloader example given the in the sdk 15.2.0. I am currently having trouble as when I try to send the file, the error shown...
hello Nordic
i am working on nrf52840, SDK16.0 developing on the peripheral app_ble_blinky example.
i am use a pin as input interrupt from other device,
if i does...
Hi,
My application uses the nrf9160dk and I program 3 Zephyr images onto the 52840: (1) bootloader, (2) image1 and (3) image2. There is no SD or anything else on the device...
Hi, I have a holyiot NRF52840 dongle (schematic below). I am able to program it via the swd interface and have BLE examples running (as long as power is attached to VDD),...
I have an application that is running the following setup as a multi-connection (peripheral and central) setup:
I am having an issue when a peripheral (NUS) is sending...
Hello everyone,
I am going to run the mesh DFU example. I found that I must use Python2, not 3 to work correctly. I follow the instruction suggested in this post.
https...
Hello, i don't know how build many project with other configuration. I want to do a lot of configurations.Then for each of them make hex files with one click of a button....
