VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
Some Examples discuss background DFU from application level, but those require bringing in IPv6 stack and TFTP client. Since we are planning to integrate DFU of our device...
I got nrf_cloud_connect failed: -111 error while running asset tracker demo.
I know that I need to flash certificate files according to my previous question: https://devzone...
It looks like the DK comes with a coin cell type battery and there seems to be a tab that can be pulled off to activate. However I don;t see any mention of this in the documentation...
Hello,
I am developing product on nrf52 with sd s112_nrf52810_5.1.0_softdevice. My application caused unexpected sd fault at adress 0x000089B2. I expect it to be something...
Hi all,
I am using my android ble application , but I don't manage to receive data sent from the application to the device ( nrf52840 )
I am using the ble_app_uart example...
Hi all, I got the requirement to actually know the path of a message from a client to server(s). Is it possible to add a few bytes of data until the message reaches the server...
Hi
I'm using NRF52840 + SDK15.0.0 and softdevice 6.0.0
I have joined two program one is ble_app_uart and other SAADC capturing ultrasound noise. (Saadc program works perfectly...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
I'm developing in a freeRTOS environment. One thread is sampling the ADC using PPI at 200Hz, which various other threads sample Sensors via SPI and finally I'm using the NRF_LOG...
Hi,
I'm designing custom PCB with nRF52832QFAA chip and after custom PCB population I can't make SWD to get working. In order to eliminate where the issue is I would like...
Hi,
I have RF-BM-ND01 (nrf51822) BLE4.0 module and i am programming it using nrfjprog tool. and i am using nrf SDK12 to program examples. i tried to flash softdevice S130...
I am using SoftDevice S132 v3.1.0 and I have a high priority application ISR that cannot tolerate being interrupted by the SoftDevice. The ISR occurs once every connection...
I'm trying to understand the limitations and configuration options for the mesh stack, in particular what happens when the mesh becomes busy.
From studying the code it appears...
I saw in the ble_app_ancs_c routine, the broadcast initialization function has the following definition：
init.advdata.uuids_solicited.uuid_cnt = sizeof(m_adv_uuids) / sizeof...
I tried to upgrade only a part of firmware of application, not all. I used buttonless DFU and found that the new code was located at bank1 and not moved at the specified address...
