I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I don't want to use MESH， because there are too many data
Application scenario
Mobile phone ------------> DeviceA --------------------------------------> DeviceB
...
Hello,
Would there be any particularly adverse side-effect if two NRF51822 GPIO pins (e.g., P0.18 and P0.19) were shorted together? One of the pins (e.g., P0.18) would be...
SDK ：15.0.0
Examples：ble_peripheral / ble_app_uart / pca10056 / s140
Board：nRF52840 DK
After pairing, may be connected, because the indicator lights continue to shine...
Hi,
I am using sd_ble_gatts_characteristic_add to set a characteristic in my service. The function call return 0 - NRF_SUCCESS but when I browse the service with nRF connect...
Hello,
I try to add pairing functionality to my app. Error code NRF_ERROR_INVALID_PARAM occur from the sd_ble_gap_sec_params_reply when i want to read my characteritic...
Hey, I have a sensor (ADC with data rate is 250 sps), attached to nrf51822. It has Data ready pin (output), which toggles from high to low when data is ready. Also this sensor...
Hi, I'm using nRF52832 with my custom board. (sdk 15.0.0)
I changed ble_uart example code, so I can receive GPS data through bluetooth.
Now, I have to send GPS data to...
Hello all.
few years ago, I made some product using nRF51822 on SDK v10.0.0
currently, I have to software update to use ECC(Elliptic Curve Cryptography) function on...
I'm using: nrf52832, SDK 15.0, SoftDevice S132 v6.0.
I'm trying to control a motor using an H-Bridge. If I simply do a nrf_gpio_pin_write to set forward/reverse to 1/0 or...
I have the nRF52832 PCA10040, V1.2.1, 2017.23 development board with ble_app_blinky_gcc_nrf52.ld RAM/FLASH settings:
MEMORY { FLASH (rx) : ORIGIN = 0x26000, LENGTH = 0x5a000...
Hi,
My freertos based application (SDK14.2) calls battery monitoring procedure every few minutes .
I've initialized the SAADC
Within the function I call
...
Hello, I have nrf52 and configure uart0 for connection with external device. I have configured it as NRF_SERIAL_MODE_DMA and set irq_handler .receive NRF_SERIAL_EVENT_DRV_ERR...
Hi,
May I ask, why read_resp is missing in struct ble_hid_report_record_t in sdk 15? Currently, I am migrating to sdk 15 from sdk 14.2. However, I didn't find any document...
Hi all,
I am doing an evaluation on NRF52 Smart Remote 3 for my company.
I am working on a Ubuntu 16.04 virtual machine with Ubuntu live CD for Smart Remote 3
-----...
