void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
I am trying to use mcuboot with external flash on the NRF52840DK with NCS2.7.0 and a simple hello world application to reproduce the problems I have with my real-world application...
We want to interface the SE050 NXP IC with the NRF5340 using the I2C protocol and generate an AES-256 key.
Could you please assist us in generating the AES-256 key using...
I tested on nrf5_sdk_17.1.0_ddde560，Tested on nrf5_sdk_17.1.0_ddde560\examples\ble_peripheral\ble_app_hrs_freertos project。Call the testfun function to test the test。
The...
Normally when I connected the nPM1300 it would automatically display the battery status and settings,
I already switched up the npm1300 but none ofthem work here.
Is...
Hi
I am working on a project which uses distance measurement config for multiple peripherals with long range.
Our plan is to support DM for up to range 25m and we observed...
I want to achieve time synchronization over a wireless connection with sub-microsecond latency. While PTP (Precision Time Protocol) can provide nanosecond-level accuracy on...
Hi, Nordic Bluetooth Controller Teams, I have a question. I see that the Aux offset of Bluetooth extended broadcast on NCS is fixed at 330us. What is the consideration behind...
Hi,
Is there a Zephyr sample project on QSPI with nRF52840? What I want to do is to write/read to an external flash (W25Q16JVSNIM).
Thank you
Best regards
Dav...
Hello,
I work on a thingy52 since few weeks with a nrf52832 SoC. When i'm turning it on and connecting it to my computer, there is no led turn on and it is not detected...
Im currently working on BLE SMP DFU on Nordic52840DK (Connect SDK v2.7.0) based on this example:
https://github.com/hellesvik-nordic/samples_for_nrf_connect_sdk/tree/main...
Hello everyone,
I am working on a project with a Thingy91 that has an nRF52840 and an nRF9160 , and I am trying to read the battery level. I want to measure this battery...
In ticket Case ID 290251, Torsten Rasmussen provides the following advice to ensure that the toolchain corresponding to the SDK is used to build the SDK (this applies to nrfutil...
I am lab testing Nordic's DECT-NR+ (DECT) for a new factory automation application; I am using the hello_dect sample application from the PHY webinar demo, I am trying to...
I made a custom board, uploaded the Arduino bootloader and was flashing the firmware with Arduino I used it without any problem with revision 2 But when I use revision 3 chip...
