Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Support Team,
Hardware : nRF5340 Custom board
Software : nRF Connect SDK v2.2.0
I have implemented OTA FW update for nRF5340. I've used multi-image simultaneous...
Hello ,
i am trying to find out advertisement handler while SD advertising in SYSTEM ON mode.
i have added a simple counter to see if it is increasing or not but it is...
Hello fellow developers!
I am currently working on a scale application using the nRF52 DK, and I've run into a roadblock regarding the integration of the HX711 load cell...
Good morning,
I would like to know if I can work with Zephyr with C++ and how to do it.
development software, with versions:
Windows 11
nRF52840-DK PCA10056, 3...
Hello
I'm suing the smp_svr sample from the Zephyr SDK 2..6.1
I want to change the CONFIG_MCUBOOT_IMAGE_VERSION to force the OTA DFU ( over bluetooth ) but when I add...
Hello Nordic Team,
I am writing because I encountered an issue while developing a BLE application on the nRF5340 development board. Currently, I have set up this callback...
With multiple of the provided samples with the SDK, I'm getting a repeated build loop that ultimately fails due to a remaining "dirty build.ninja". This is primarily with...
Hi,
I am working BT840F which has nrf52840, I am using ble_app_uart example to transfer UART data to app. I wanted to know what is the system frequency of the microcontroller...
Hi,
I am using an external flash on the NRF52840DK via SPI and have established working communication with the flash memory. However, I need to disable CONFIG_SPI...
In my project, using nrf52840 controller, I am trying to store 253 bytes of data in NVM, but I encounter an error: "flash_nrf: invalid address: 0x00100ff8:8." Is there any...
Hello DevZone,
I'm porting my project from NCS 2.5.0 to NCS 2.7.0.
I know that there are lots of changes in build system, especially in Zephyr sysbuild. So, I decided...
Hello, I was able to update nRF Connect SDK to v2.7.0 fine using nRF Connect for Desktop. However, the nRF Connect for VS Code extension update v2024.7.13 causes VS Code launch...
Hi,
As described in the subject I'm not able to set "Extra High Drive" for a GPIO. This setting is described in 7.13.5.11 in product specification version 1.3. I'm able...
