Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
HI
Based on the nRF54L15 with SDK 3.0.0 and MCUBOOT for OTA updates, I've discovered there's a firmware image compression algorithm available. However, when compiling with...
Hi Team,
We are using nRF9160 MQTT sample code 'mqtt_simple'.
1. What is the maximum payload we can send in one single PUBLISH?
2. I want to send 4KB of data in single...
Hello,
for some time I didn't have to work on my project that uses nRF Connect SDK but recently I had to work on it again and noticed that I am not able to build my before...
Hi,
I am trying to create a trilateration system with 3 initiators and 1 reflector (Hopefully multiple reflectors in the future) on the nrf54l15. The channel sounding with...
When running the NRF Connect SDK SoftAP sample, connected stations disconnect at **exactly 5 minutes** (300 seconds) into the session, regardless of activity or configuration...
Hello support,
For our project we have an integration with Memfault for metrics, coredumps and log files.
We are currently developing in NRF 2.7.0 on a nrf9160 chip. ...
My SPI slave sensor requires a 32-bit frame length. The CS (Chip Select) signal needs to be switched for each 32-bit frame interval, and it also supports DMA (Direct Memory...
Hi ,
I am using skb501 module and which contains nrf52840.I am using nrf5sdk for development for zigbee coordinator because nrf connect sdk is not supportable in this...
Hello!
We are developing a device based on the nRF5340 and using SDK v2.6.0. The firmware implements a USB composite device (CDC ACM + MIDI + Audio). Everything works perfectly...
I am attempting to interface a tas2110 with an nrf52840. I just became aware of some nrf52 limitations and wanted to get the latest info. My requirements are as follows "The...
as shown in this document:
https://www.bluetooth.com/wp-content/uploads/Files/Specification/HTML/Core-54/out/en/host/attribute-protocol--att-.html and Zephyr's att.h , 0x0d...
When I run the peripheral_hids_mouse sample, I scan/connect on nrf connect and see an instance of the peripheral. then if I clear and scan again in the Discovered devices...
The J-Link itself can’t “see” the external flash — it only talks to the nRF5340’s CPU via SWD. I would like to program initial image of the external flash. 1. On Segger website...
Hi,Team,
I'm currently using the nrf54l15-dk. I want to implement our custom app to send firmware data to the nrf54l15-dk, have the nrf54l15-dk receive the firmware data...
Hi, I have two nRF52840-DK boards and I'm testing matter light bulb example.
If I load the project in one board it works fine when I link it with virtual assistant like...
