Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hello all,
I am developing on the nRF52840, and I am using the PCA10056/nRF52840-DK to assist in my understanding of the uploading process.
Currently, I am trying to get...
What is the reason Nordic dont want to provide yet dual mode solution - BR/EDR + BLE? - There are plenty of legacy BT devices on the market and the new BLE devices doesnt...
I am working on developing an application for nRF52833 DK (PCA10100) using nRF5 SDK_v17.1 and nRF_802.15.4 Radio driver v1.6. I am using the s122 Soft device on the device...
Hi all,
So I was following this guide for updating my firmware over BLE: https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu#dfu_over_bluetooth...
Mesh SDK 5.0, SoftDevice S140 v7.2.0, NRF52840, SEGGER ------------------------------------------------------------------------------------ Hello, My problem is that I can...
When i open the Toolchain on my mac it loads and put upp a crash page. i have already: restarted my mac, reintstalled and restarted but i get the same crash
The System...
Hi, I currently have a project with an nRF52832 chip using SDK 14.2, I would like to upgrade the project and change the chip to nRF5340. Is there a way to migrate the project...
Are there any examples showing use of the MQTT library using Bluetooth as the Link Layer? I see this on Zephyr's repo zephyr/subsys/net/l2/bluetooth at main · zephyrproject...
Here is a warning I get linking an application that uses nRF DM library 5/14] Linking C static library app\libapp.a [6/14] Linking C executable zephyr\zephyr_pre0.elf c:/toolchains...
Hi,
Can any one list what are the reasons for sd_ble_gap_connect returns NRF_ERROR_DATA_SIZE?
In ble_gap.h NRF_ERROR_DATA_SIZE error code doesn't exist for sd_ble_gap_connect...
Hello,
We have already product with BLE 4 and now we are moving to BLE5. As per the example code we have updated our code to BLE 5 but we are not seeing advertisement...
Purpose: to develop a central device using nRF5340 and to enable both BLE Mesh and AoA features.
Questions:
1. nRF5 SDK supports nRF51 and nRF52 series but not for nRF5340...
Hello,
We were middle way during the development when we found out that we had a higher packet loss than what is acceptable.
So we start to analyze this issue.
Scenario...
Hi,
I reviewed the PCA10121 schematic for using SPI4 pins to connect to Semtech SX1262. Since SPI4 bus also connected to SD card and DSP. I checked to see if SPI0..3 pins...
