Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
I am using NCS v2 and VSCode extension on Windows 11.
I have two pieces of hardware I am testing with:
Adafruit nRF52840 Feather
Custom nRF52840 board
When I flash...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
I would like to automate some unit tests with NCS. I tried running the native_posix qemu builds, however, this does not support the mac m1 architecture (maybe Linux only?...
I'm updating the NCS we are using from 2.0.2 to 2.1.0 in order to use the modem firmware 1.3.3 that was just released. I verified my build with NCS 2.0.0, 2.0.1 and 2.0.2...
Hello!
I use NRF Connect SDK 1.8.0, but peripherials are configured using nrfx library.
My task is to implement serial interface where I have PIN_TX and PIN_RX. I transmit...
Hello All,
I have few questions below:
- Does the ENABLE input disconnect the internal power systems completely, or does the circuit remain in some mode and nevertheless...
Hi Sir,
I am testing the NDT w/ example "nRF_DM" (NCS 2.0.0), there are two nRF52840-DK for this test. When two boards link success, the terminal starts to show the log...
Hello everyone
In the company I work for, we make a special kind of dongles which are able to connect to smartphones through BLE and transfer data.
I have 4 of these dongles...
Hi there,
I am working on a door lock project using nRF 52840 DKs and nRF5 SDK for Thread and Zigbee v4.2.0. we are having both ZigBee and BLE protocols in it. I started...
Hi everyone,
I'm trying to implement directed advertising on the BLE codeded PHY.
My setup of consists of two identical NRF5340 based custom boards, running FW based on...
Hi, nice to e-meet you. I want to use nRF52810 pin 25 (or other pins) to drive an external board, and through it to control the external board switch.
I set the pin to H0H1...
Hello,
I am currently working with pc-ble-driver-py and have observed write operations taking an exceedingly long time. Previous DevZone posts on this topic seem to be unresolved...
Hi,
Sorry to seek help again but I cant solve this issue
Steps
1 - nrfjprog -f nrf52 --eraseall
2 - nrfjprog -f nrf52 --program mbr.hex --sectorerase --verify
With...
